10 open source boards using the LoRa-E5
Real designs built with the LoRa-E5, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Tinynode
Stary2001
80 × 60 mm63 parts4LCERN-OHL-P-2.02Sending Pebble
CohenMurray
50 × 50 mm60 parts4LNo license1DDRN Hardware
davidfobar
33.3 × 54.5 mm51 parts2LNo license1ESP32
Tbogg-Sensor-Package
UofC-GNCTR-2024
52 × 67 mm40 parts2LMIT1Pcb power
nobodywasishere
41.3 × 28.6 mm34 parts2LApache-2.01RP2040/RP2350
Wireless Slave
magnusbpt
62 × 57 mm85 parts2LNo license0ESP32
AquaBoard
Lekylouch
98.7 × 55.6 mm62 parts2LNo license0Ultramote
etrommer
40 × 42.5 mm54 parts2LGPL-3.00STM32
Projet ETRS 528
B1jam1-74
88.1 × 70 mm52 parts2LMIT0AVR/Arduino
Modbus master
magnusbpt
104 × 129 mm77 parts2LNo license0
How designs wire the LoRa-E5
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the LoRa-E5 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 8 of 9 designs, most often 4.7 µF (then 100 nF).
- The PB0 pin is left unconnected on 9 of 9 designs.
- The PB5 pin is left unconnected on 7 of 9 designs (a signal on 2).
- The PB4 pin is left unconnected on 6 of 9 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: 3.3V 89% |
|
| GNDpin 2, 14, 16, 22 | Connected to: GND 100% | — |
| PB15pin 5 | Connected to: Signal 56% · not connected 44% |
|
| PA15pin 6 | Connected to: Signal 56% · not connected 44% |
|
| PB4pin 7 | Connected to: Not connected 67% · a signal 33% | — |
| PB3pin 8 | Connected to: Not connected 67% · a signal 33% | — |
| PB7pin 9 | Connected to: A connector 33%, the microcontroller 22% |
|
| PB5pin 11 | Connected to: Not connected 78% · a signal 22% | — |
| PC1pin 12 | Connected to: Not connected 67% · a signal 33% | — |
| PC0pin 13 | Connected to: Not connected 67% · a signal 33% | — |
| RFIOpin 15 | Connected to: A connector 44% |
|
| PB0pin 28 | Connected to: Not connected 100% | — |
13 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Tinynode by Stary2001, Sending Pebble by CohenMurray, DDRN Hardware by davidfobar and Pcb power by nobodywasishere.
The LoRa-E5 in open source designs
The gallery holds 10 open source boards using the LoRa-E5 from 9 GitHub repositories; a typical one measures about 57 × 56.3 mm and carries around 57 components.
80% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Tinynode by Stary2001.
Parts used alongside the LoRa-E5
Microcontrollers on boards using the LoRa-E5
What boards using the LoRa-E5 are built for
LoRa-E5: common questions
Where can I find a LoRa-E5 reference design?
Each of the 10 boards on this page is a real design using the LoRa-E5. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LoRa-E5 VCC pin?
The VCC pin has a decoupling capacitor on 8 of 9 designs, most often 4.7 µF (then 100 nF). Counted from the KiCad layouts of 9 open source designs using the LoRa-E5.
How is the LoRa-E5 PB0 pin connected?
The PB0 pin is left unconnected on 9 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the LoRa-E5.
How is the LoRa-E5 PB5 pin connected?
The PB5 pin is left unconnected on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the LoRa-E5.
Which microcontrollers do boards using the LoRa-E5 use?
Most are built on ESP32 (2), AVR/Arduino (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the LoRa-E5?
The median is 57 × 56.3 mm, and 80% are two-layer designs.
What is the most popular open source board using the LoRa-E5?
By GitHub stars, Tinynode by Stary2001, with 2 stars.
Can I simulate one of these boards using the LoRa-E5 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.