13 open source boards using the LSM6DSO
Real designs built with the LSM6DSO, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Imu rc hand unit
DimitriOnLSD
35 × 50 mm73 parts2LMIT7Nordic nRF
Revolutetestboard
tongtongwang86
54 × 85.7 mm254 parts4LCC-BY-NC-4.05ESP32
Haptic knob
wirano
50 × 50 mm66 parts4LNo license3ESP32
Chronos phantom
jayis1
65 × 30 mm26 parts4LNo license3AVR/Arduino
Jazzhands main
wearpants
64.9 × 33 mm32 parts2LNo license1RP2040/RP2350
Dragonfly v0 1
aravindjayan
40 × 59.2 mm76 parts2LNo license0Nordic nRF
IDE
RishobanK
50 × 35 mm8 parts4LNo license0POVshield4.1
shurik179
58.9 × 18.8 mm20 parts2LMIT43NXP
WearablePocketometer
kwan3217
66 × 38.1 mm81 parts2LGPL-2.02ESP32
NoU3-Panelized
AlfredoSystems
138 × 168 mm113 parts4LNo license1RP2040/RP2350
Dragonfly v0-1 Ribs
aravindjayan
52 × 71.2 mm76 parts2LNo license0Shoulder
kwan3217
38.1 × 25.4 mm35 parts2LGPL-2.02NXP
Pocket
kwan3217
66 × 38.1 mm31 parts2LGPL-2.02
How designs wire the LSM6DSO
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the LSM6DSO connects to, and the resistors, capacitors and other passives placed on it.
- The VDDIO pin has a decoupling capacitor on 6 of 9 designs, most often 100 nF (then 1 µF).
- The VDD pin has a decoupling capacitor on 6 of 9 designs, most often 100 nF (then 1 µF).
- The INT2 pin is left unconnected on 7 of 9 designs.
- The SCL pin has a pull-up to 3.3V on 5 of 8 designs, most often 10 kΩ (then 3.3 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDIOpin 5 | Connected to: 3.3V 67% · a signal 22% |
|
| GNDpin 6, 7 | Connected to: GND 78% · a signal 22% | — |
| VDDpin 8 | Connected to: 3.3V 78% · a signal 22% |
|
| INT2pin 9 | Connected to: Not connected 78% | — |
| NCpin 10, 11 | Connected to: Not connected 100% | — |
| SCLpin 13 | Connected to: A connector 38%, the microcontroller 38% |
|
| SDApin 14 | Connected to: A connector 38%, the microcontroller 38% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include POVshield4.1 by shurik179, Imu rc hand unit by DimitriOnLSD, Revolutetestboard by tongtongwang86 and Haptic knob by wirano.
The LSM6DSO in open source designs
The gallery holds 13 open source boards using the LSM6DSO from 10 GitHub repositories; a typical one measures about 54 × 38.1 mm and carries around 66 components.
62% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is POVshield4.1 by shurik179.
Parts used alongside the LSM6DSO
Microcontrollers on boards using the LSM6DSO
What boards using the LSM6DSO are built for
LSM6DSO: common questions
Where can I find a LSM6DSO reference design?
Each of the 13 boards on this page is a real design using the LSM6DSO. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LSM6DSO VDDIO pin?
The VDDIO pin has a decoupling capacitor on 6 of 9 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the LSM6DSO.
What decoupling capacitors do designs use on the LSM6DSO VDD pin?
The VDD pin has a decoupling capacitor on 6 of 9 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the LSM6DSO.
How is the LSM6DSO INT2 pin connected?
The INT2 pin is left unconnected on 7 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the LSM6DSO.
Which microcontrollers do boards using the LSM6DSO use?
Most are built on ESP32 (4), Nordic nRF (2), NXP (2) and RP2040/RP2350 (2).
How big is a typical board using the LSM6DSO?
The median is 54 × 38.1 mm, and 62% are two-layer designs.
What is the most popular open source board using the LSM6DSO?
By GitHub stars, POVshield4.1 by shurik179, with 43 stars.
Can I simulate one of these boards using the LSM6DSO before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.