11 open source boards using the LTC-4627JR
Real designs built with the LTC-4627JR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Led display
eshazen
116.8 × 172.7 mm74 parts2LNo license33ESP32
VCU
sufst
194.3 × 92.8 mm205 parts4LGPL-3.019FPGA
Gecko5education
logisim-evolution
60.6 × 100 mm308 parts6LMIT18AVR/Arduino
ATMEGA8A-Tutorial-Board-I
villseriol
90 × 70 mm49 parts4LApache-2.00ESP32
Printer cabinet
Cylindric3D
150 × 40 mm25 parts2LApache-2.00ESP32
Batak
sufst
93.9 × 84 mm164 parts2LGPL-3.019ESP32
16 Channel Sensor Hub
sufst
83.4 × 46.3 mm147 parts4LGPL-3.019ESP32
8 Channel Sensor Hub
sufst
58.5 × 57.5 mm96 parts4LGPL-3.019ESP32
BSPD
sufst
60 × 47.5 mm67 parts4LGPL-3.019ESP32
Dash
sufst
235 × 73.6 mm63 parts2LGPL-3.019ESP32
TSAC Relay Controller
sufst
73 × 65.3 mm54 parts2LGPL-3.019
How designs wire the LTC-4627JR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LTC-4627JR connects to, and the resistors, capacitors and other passives placed on it.
- The NO_PIN_1 pin is left unconnected on 4 of 4 designs.
- The NO_PIN_2 pin is left unconnected on 4 of 4 designs.
- The CA1 pin has a series resistor on 2 of 5 designs, most often 40 kΩ.
- The + pin has a series resistor on 2 of 5 designs, most often 1 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CA1pin 1 | Connected to: Signal 100% |
|
| +pin 3 | Connected to: Signal 100% |
|
| -pin 4 | Connected to: Signal 60% · not connected 40% |
|
| V+pin 5 | Connected to: Signal 80% · GLV_PROT 20% |
|
| DPpin 7 | Connected to: Signal 75% · not connected 25% |
|
| NCpin 9 | Connected to: Not connected 100% | — |
| NO_PIN_1pin 10 | Connected to: Not connected 100% | — |
| Fpin 11 | Connected to: Signal 100% |
|
| NO_PIN_2pin 12 | Connected to: Not connected 100% | — |
| Cpin 13 | Connected to: Signal 100% |
|
| Apin 14 | Connected to: Signal 100% |
|
| Gpin 15 | Connected to: Signal 100% |
|
| Bpin 16 | Connected to: Signal 100% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Led display by eshazen, 16 Channel Sensor Hub by sufst, Gecko5education by logisim-evolution and Printer cabinet by Cylindric3D.
The LTC-4627JR in open source designs
The gallery holds 11 open source boards using the LTC-4627JR from 5 GitHub repositories; a typical one measures about 90 × 70 mm and carries around 74 components.
55% use four copper layers or more, and 91% carry an open source license.
The most starred is Led display by eshazen.
Microcontrollers on boards using the LTC-4627JR
What boards using the LTC-4627JR are built for
LTC-4627JR: common questions
Where can I find a LTC-4627JR reference design?
Each of the 11 boards on this page is a real design using the LTC-4627JR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LTC-4627JR NO_PIN_1 pin connected?
The NO_PIN_1 pin is left unconnected on 4 of 4 designs. Counted from the KiCad layouts of 5 open source designs using the LTC-4627JR.
How is the LTC-4627JR NO_PIN_2 pin connected?
The NO_PIN_2 pin is left unconnected on 4 of 4 designs. Counted from the KiCad layouts of 5 open source designs using the LTC-4627JR.
What resistor goes on the LTC-4627JR CA1 pin?
The CA1 pin has a series resistor on 2 of 5 designs, most often 40 kΩ. Counted from the KiCad layouts of 5 open source designs using the LTC-4627JR.
Which microcontrollers do boards using the LTC-4627JR use?
Most are built on ESP32 (8), AVR/Arduino (1) and FPGA (1).
How big is a typical board using the LTC-4627JR?
The median is 90 × 70 mm, and 45% are two-layer designs.
What is the most popular open source board using the LTC-4627JR?
By GitHub stars, Led display by eshazen, with 33 stars.
Can I simulate one of these boards using the LTC-4627JR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.