9 open source boards using the LTV-814
Real designs built with the LTV-814, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AlimTeleinfoMySensors
tdouez
21.9 × 17.1 mm14 parts2LNo license14STM32
Led controller hardware
markus-k
100 × 67 mm88 parts2LTAPR-OHL-1.05AVR/Arduino
MySensors 8Dimmers
LudovicLemarinel
100 × 100 mm66 parts2LNo license4AVR/Arduino
Controller
Technariumas
240 × 125 mm268 parts2LApache-2.00ESP32
Supla ESP32 LAN
jaku2019
209 × 85.5 mm211 parts2LNo license0Epanel energy monitor
mylife-home
103 × 86.5 mm143 parts2LGPL-3.00STM32
Radiant
VersBinarii
89 × 41.5 mm47 parts4LNo license0ESP8266
8Dimmers
LudovicLemarinel
100 × 100 mm74 parts2LNo license3ESP32
Prototype-3
mylife-home
100 × 100 mm68 parts2LGPL-3.00
How designs wire the LTV-814
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LTV-814 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 6 of 8 designs, most often 100 kΩ (then 47 kΩ).
- Pin 3 is tied to GND on 5 of 8 designs (a signal on 3).
- Pin 2 has a series resistor on 4 of 8 designs, most often 100 kΩ (then 330 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 88% |
|
| Pin 2 | Connected to: A connector 38% |
|
| Pin 3 | Connected to: GND 63% · a signal 38% | — |
| Pin 4 | Connected to: The microcontroller 25% · VCC 25% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AlimTeleinfoMySensors by tdouez, Led controller hardware by markus-k, MySensors 8Dimmers by LudovicLemarinel and 8Dimmers by LudovicLemarinel.
The LTV-814 in open source designs
The gallery holds 9 open source boards using the LTV-814 from 8 GitHub repositories; a typical one measures about 100 × 86.5 mm and carries around 74 components.
89% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is AlimTeleinfoMySensors by tdouez.
Parts used alongside the LTV-814
Microcontrollers on boards using the LTV-814
What boards using the LTV-814 are built for
LTV-814: common questions
Where can I find a LTV-814 reference design?
Each of the 9 boards on this page is a real design using the LTV-814. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LTV-814 pin 1?
Pin 1 has a series resistor on 6 of 8 designs, most often 100 kΩ (then 47 kΩ). Counted from the KiCad layouts of 8 open source designs using the LTV-814.
How is the LTV-814 pin 3 connected?
Pin 3 is tied to GND on 5 of 8 designs (a signal on 3). Counted from the KiCad layouts of 8 open source designs using the LTV-814.
What resistor goes on the LTV-814 pin 2?
Pin 2 has a series resistor on 4 of 8 designs, most often 100 kΩ (then 330 Ω). Counted from the KiCad layouts of 8 open source designs using the LTV-814.
What parts are used alongside the LTV-814?
The MOC3023M, TRIAC_small and ULN2803A appear in the most repositories here.
Which microcontrollers do boards using the LTV-814 use?
Most are built on AVR/Arduino (2), ESP32 (2), STM32 (2) and ESP8266 (1).
How big is a typical board using the LTV-814?
The median is 100 × 86.5 mm, and 89% are two-layer designs.
What is the most popular open source board using the LTV-814?
By GitHub stars, AlimTeleinfoMySensors by tdouez, with 14 stars.
Can I simulate one of these boards using the LTV-814 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.