8 open source boards using the MOC3023M
Real designs built with the MOC3023M, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
LiBCM
doppelhub
355 × 160 mm706 parts4LCC-BY-SA-4.025AVR/Arduino
HotAirGun
raspibo
104.1 × 82.6 mm68 parts2LNo license16AVR/Arduino
MySensors 8Dimmers
LudovicLemarinel
100 × 100 mm66 parts2LNo license4Dimmer
drkntz
99.1 × 69.9 mm47 parts2LNo license0AVR/Arduino
ControleurFilPiloteSMS
MathieuBahin
87 × 83.6 mm18 parts2LNo license0ESP8266
8Dimmers
LudovicLemarinel
100 × 100 mm74 parts2LNo license3Leading edge ac dimmer
niliha
54 × 96 mm57 parts2LGPL-3.01Leading edge ac dimmer.bak
niliha
47.6 × 30.5 mm21 parts2LGPL-3.01
How designs wire the MOC3023M
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MOC3023M connects to, and the resistors, capacitors and other passives placed on it.
- Pin 6 has a series resistor on 6 of 7 designs, most often 100 Ω (then 4.7 kΩ).
- Pin 1 has a series resistor on 3 of 7 designs, most often 330 Ω (then 470 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| NCpin 3, 5 | Connected to: Not connected 100% | — |
| Pin 6 | Connected to: Signal 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include LiBCM by doppelhub, HotAirGun by raspibo, MySensors 8Dimmers by LudovicLemarinel and 8Dimmers by LudovicLemarinel.
The MOC3023M in open source designs
The gallery holds 8 open source boards using the MOC3023M from 7 GitHub repositories; a typical one measures about 99.5 × 89.8 mm and carries around 62 components.
88% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is LiBCM by doppelhub.
Parts used alongside the MOC3023M
Microcontrollers on boards using the MOC3023M
What boards using the MOC3023M are built for
MOC3023M: common questions
Where can I find a MOC3023M reference design?
Each of the 8 boards on this page is a real design using the MOC3023M. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MOC3023M pin 6?
Pin 6 has a series resistor on 6 of 7 designs, most often 100 Ω (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the MOC3023M.
What resistor goes on the MOC3023M pin 1?
Pin 1 has a series resistor on 3 of 7 designs, most often 330 Ω (then 470 Ω). Counted from the KiCad layouts of 7 open source designs using the MOC3023M.
Which microcontrollers do boards using the MOC3023M use?
Most are built on AVR/Arduino (3) and ESP8266 (1).
How big is a typical board using the MOC3023M?
The median is 99.5 × 89.8 mm, and 88% are two-layer designs.
What is the most popular open source board using the MOC3023M?
By GitHub stars, LiBCM by doppelhub, with 25 stars.
Can I simulate one of these boards using the MOC3023M before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.