15 open source boards using the MAX3051
Real designs built with the MAX3051, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
QUarkNano 9250 UC4H
ukmook
21.5 × 30 mm61 parts4LCC-BY-SA-4.010STM32
Can io board
cvra
16.4 × 20.1 mm22 parts2LCustom license10STM32
STM32G431
Jana-Marie
60 × 44 mm154 parts4LCERN-OHL-1.29STM32
MoxiE Control board
Teslafly
65 × 56 mm175 parts4LMIT5STM32
Actuator board
cvra
22 × 40 mm52 parts4LCustom license2ESP32
Capable jetson carrier
CapableRobot
100 × 55 mm344 parts6LApache-2.00STM32
ORION VV driver v3
ibis-ssl
52.4 × 123.1 mm119 parts4LNo license0Moteus controller
AeroX2
46 × 53 mm100 parts4LNo license0STM32
Can uart board
bpmasc
58 × 45 mm59 parts2LNo license0STM32
Hw sense
MaxBaex
47.8 × 23.1 mm58 parts4LCC-BY-SA-4.00STM32
PX4FMUv2.4
lachlanA
70 × 40.5 mm351 partsGPL-2.0429STM32
PAC5523
Jana-Marie
60 × 44 mm126 parts4LCERN-OHL-1.29ESP32
CRMHJN capable carrier
CapableRobot
122 × 77 mm344 parts6LApache-2.00STM32
Canon 2019
cocobot
30 × 50 mm79 parts2LNo license2Rtihu
AMSAT-NA
92 × 92 mm295 parts4LNo license4
How designs wire the MAX3051
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the MAX3051 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 13 of 13 designs, most often 100 nF (then 2.2 µF).
- The CANH pin has a series resistor on 9 of 13 designs, most often 120 Ω (then 402 Ω).
- The CANL pin has a series resistor on 8 of 13 designs, most often 120 Ω (then 603 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VDDpin 3 | Connected to: 3.3V 92% |
|
| CANLpin 6 | Connected to: A connector 85% |
|
| CANHpin 7 | Connected to: A connector 85% |
|
| RSpin 8 | Connected to: GND 54% · a signal 46% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PX4FMUv2.4 by lachlanA, Can io board by cvra, QUarkNano 9250 UC4H by ukmook and PAC5523 by Jana-Marie.
The MAX3051 in open source designs
The gallery holds 15 open source boards using the MAX3051 from 13 GitHub repositories; a typical one measures about 58 × 45 mm and carries around 119 components.
79% use four copper layers or more, and 53% carry an open source license.
The most starred is PX4FMUv2.4 by lachlanA.
Parts used alongside the MAX3051
What boards using the MAX3051 are built for
MAX3051: common questions
Where can I find a MAX3051 reference design?
Each of the 15 boards on this page is a real design using the MAX3051. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MAX3051 VDD pin?
The VDD pin has a decoupling capacitor on 13 of 13 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 13 open source designs using the MAX3051.
What resistor goes on the MAX3051 CANH pin?
The CANH pin has a series resistor on 9 of 13 designs, most often 120 Ω (then 402 Ω). Counted from the KiCad layouts of 13 open source designs using the MAX3051.
What resistor goes on the MAX3051 CANL pin?
The CANL pin has a series resistor on 8 of 13 designs, most often 120 Ω (then 603 Ω). Counted from the KiCad layouts of 13 open source designs using the MAX3051.
Which microcontrollers do boards using the MAX3051 use?
Most are built on STM32 (11) and ESP32 (2).
How big is a typical board using the MAX3051?
The median is 58 × 45 mm, and 21% are two-layer designs.
What is the most popular open source board using the MAX3051?
By GitHub stars, PX4FMUv2.4 by lachlanA, with 429 stars.
Can I simulate one of these boards using the MAX3051 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.