6 open source boards using the MC6800
Real designs built with the MC6800, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Fennec6800
ChartreuseK
218 × 131.9 mm113 parts2LBSD-3-Clause20Peoples permacomputer
genossen
208.3 × 146.1 mm121 parts2LCustom license2MEZ6800
satoshiokue
28 × 60 mm4 parts2LMIT1Mainboard
btb
414.3 × 266.7 mm155 parts2LNo license0GIMIX Ghost 6800
roberto314
228.6 × 142.2 mm74 parts2LBSD-2-Clause1PIC
MECB 6800 CPU
epaell
99.8 × 99.8 mm14 parts2LNo license6
How designs wire the MC6800
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MC6800 connects to, and the resistors, capacitors and other passives placed on it.
- The IRQ pin has a pull-up to 5V on 5 of 6 designs, most often 10 kΩ (then 2.2 kΩ).
- The TSC pin is tied to GND on 5 of 6 designs.
- The NMI pin has a pull-up to VCC on 4 of 6 designs, most often 10 kΩ.
- The HALT pin has a pull-up to VCC on 3 of 6 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 1, 21 | Connected to: GND 100% | — |
| HALTpin 2 | Connected to: A connector 33% |
|
| PHI1pin 3 | Connected to: Signal 100% |
|
| IRQpin 4 | Connected to: A connector 83% |
|
| NMIpin 6 | Connected to: A connector 67% · 5V 17% |
|
| VCCpin 8 | Connected to: VCC 100% | — |
| N.C.pin 35, 38 | Connected to: Not connected 83% · GND 17% | — |
| PHI2pin 37 | Connected to: A connector 33% |
|
| TSCpin 39 | Connected to: GND 83% · a signal 17% | — |
| RESETpin 40 | Connected to: A connector 67% |
|
28 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Fennec6800 by ChartreuseK, MECB 6800 CPU by epaell, Peoples permacomputer by genossen and GIMIX Ghost 6800 by roberto314.
The MC6800 in open source designs
The gallery holds 6 open source boards using the MC6800 from 6 GitHub repositories; a typical one measures about 213.1 × 137 mm and carries around 94 components.
100% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Fennec6800 by ChartreuseK.
Parts used alongside the MC6800
Microcontrollers on boards using the MC6800
What boards using the MC6800 are built for
MC6800: common questions
Where can I find a MC6800 reference design?
Each of the 6 boards on this page is a real design using the MC6800. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MC6800 IRQ pin?
The IRQ pin has a pull-up to 5V on 5 of 6 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 6 open source designs using the MC6800.
How is the MC6800 TSC pin connected?
The TSC pin is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the MC6800.
What pull-up resistor is used on the MC6800 NMI pin?
The NMI pin has a pull-up to VCC on 4 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the MC6800.
What parts are used alongside the MC6800?
The 2716, 74LS04, 74LS138, 74LS74 and 6116 appear in the most repositories here.
Which microcontrollers do boards using the MC6800 use?
Most are built on PIC (1).
How big is a typical board using the MC6800?
The median is 213.1 × 137 mm, and 100% are two-layer designs.
What is the most popular open source board using the MC6800?
By GitHub stars, Fennec6800 by ChartreuseK, with 20 stars.
Can I simulate one of these boards using the MC6800 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.