5 open source boards using the MCP1640CH

Real designs built with the MCP1640CH, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the MCP1640CH

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MCP1640CH connects to, and the resistors, capacitors and other passives placed on it.

  • The SW pin has a inductor on 5 of 5 designs, most often 4.7 µH.
  • The VFB pin has a resistor to GND on 5 of 5 designs, most often 562 kΩ (then 309 kΩ).
  • The VOUT pin has a capacitor to GND on 5 of 5 designs, most often 10 µF (then 47 µF).
  • The VIN pin has a capacitor to GND on 5 of 5 designs, most often 10 µF (then 4.7 µF).
SWpin 1Connected to: Signal 100%
  • Inductor on 100% · 4.7 µH (3)
GNDpin 2Connected to: GND 100%
ENpin 3Connected to: AP22811 60%, AXP209 40% · 3.3V 20%
  • Resistor to GND on 80% · 100 kΩ (3), 47 kΩ (1)
VFBpin 4Connected to: Signal 100%
  • Resistor to GND on 100% · 562 kΩ (3), 309 kΩ (1), 470 kΩ (1)
  • Series resistor on 60% · 976 kΩ (3)
  • Pull-up to 5V on 40% · 976 kΩ (1), 270 kΩ (1)
VOUTpin 5Connected to: AP22811 60% · 5V 40%
  • Capacitor to GND on 100% · 10 µF (4), 47 µF (1)
  • Series resistor on 60% · 976 kΩ (3)
VINpin 6Connected to: AP61100 40%, AXP209 40% · 3.3V 40%
  • Capacitor to GND on 100% · 10 µF (11), 4.7 µF (5), 100 nF (1)
  • Inductor on 100% · 4.7 µH (3)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Sbc allwinner a13 by vd-rd, Sbc allwinner v3s by vd-rd, Mesp240 opll by hwreverse and Sbc allwinner F1C200s by vd-rd.

The MCP1640CH in open source designs

The gallery holds 5 open source boards using the MCP1640CH from 5 GitHub repositories; a typical one measures about 66 × 44 mm and carries around 105 components.

60% use four copper layers or more, and 20% carry an open source license.

The most starred is Sbc allwinner a13 by vd-rd.

Microcontrollers on boards using the MCP1640CH

MCP1640CH: common questions

Where can I find a MCP1640CH reference design?

Each of the 5 boards on this page is a real design using the MCP1640CH. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MCP1640CH SW pin connected?

The SW pin has a inductor on 5 of 5 designs, most often 4.7 µH. Counted from the KiCad layouts of 5 open source designs using the MCP1640CH.

What resistor goes on the MCP1640CH VFB pin?

The VFB pin has a resistor to GND on 5 of 5 designs, most often 562 kΩ (then 309 kΩ). Counted from the KiCad layouts of 5 open source designs using the MCP1640CH.

How is the MCP1640CH VOUT pin connected?

The VOUT pin has a capacitor to GND on 5 of 5 designs, most often 10 µF (then 47 µF). Counted from the KiCad layouts of 5 open source designs using the MCP1640CH.

What parts are used alongside the MCP1640CH?

The AP22811, USBLC6-2P6, AP61100, AXP209 and PCA6408A appear in the most repositories here.

Which microcontrollers do boards using the MCP1640CH use?

Most are built on ESP32 (1) and STM32 (1).

How big is a typical board using the MCP1640CH?

The median is 66 × 44 mm, and 40% are two-layer designs.

What is the most popular open source board using the MCP1640CH?

By GitHub stars, Sbc allwinner a13 by vd-rd, with 38 stars.

Can I simulate one of these boards using the MCP1640CH before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part