18 open source boards using the MCP23008
Real designs built with the MCP23008, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Radioberry LPF V1.3
pa3gsb
85 × 56 mm112 parts4LNo license24Raspberry Pi
PiPtr
jmlzone
101.6 × 141.7 mm379 parts4LNo license8Alpacaboard
Sheepybloke2-0
329.4 × 97.5 mm140 parts2LNo license5NXP
HMS-Olfactometer
HMS-RIC
279.4 × 137.2 mm58 parts2LMIT3ESP8266
ESP multi board
CRM-UAM
82.2 × 47.9 mm43 parts2LNo license2PIC
Athena HW
ffich
115.1 × 95 mm133 partsNo license0ESP8266
Weather Station
scabootssca
91.4 × 68.6 mm81 parts2LGPL-3.00GPIO - MCP23008-LED
tronixio
55 × 25 mm29 parts2LNo license0FPGA
HL2 Filter Board
softerhardware
100 × 49.9 mm112 parts4LNo license372AVR/Arduino
Avr ledprojection-0402
cnlohr
25.4 × 34.5 mm91 parts2LMIT4ESP8266
ESP multi board cuadrada
CRM-UAM
61 × 35.6 mm24 parts2LNo license2ESP8266
Sram redo
scabootssca
271.8 × 185.4 mm81 parts2LGPL-3.00TunerSection
profdc9
100 × 100 mm123 parts2LNo license59AVR/Arduino
ControlStandShield
RobertPHeller
68.6 × 53.3 mm40 parts2LGPL-3.03Elliott 903 Control Panel
jonathan-tooley
431.8 × 114.3 mm52 parts2LNo license0LittleDelayLine
profdc9
100 × 100 mm117 parts2LNo license59LittleSwitchBus
profdc9
100 × 100 mm101 parts2LNo license59Filter
profdc9
100 × 100 mm81 parts2LNo license59
How designs wire the MCP23008
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the MCP23008 connects to, and the resistors, capacitors and other passives placed on it.
- The INT pin is left unconnected on 12 of 13 designs.
- The SCL pin has a pull-up to 5V on 7 of 13 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The SDA pin has a pull-up to 5V on 7 of 13 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The A2 pin is tied to GND on 8 of 13 designs (VDD on 2, a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCLpin 1 | Connected to: A connector 46%, the microcontroller 31% |
|
| SDApin 2 | Connected to: A connector 46%, the microcontroller 31% |
|
| A2pin 3 | Connected to: GND 62% · VDD 15% · a signal 23% | — |
| A0pin 5 | Connected to: GND 62% · a signal 23% | — |
| NCpin 7 | Connected to: Not connected 100% | — |
| INTpin 8 | Connected to: Not connected 92% | — |
| VSSpin 9 | Connected to: GND 85% · a signal 15% | — |
| GP0pin 10 | Connected to: Signal 69% · not connected 31% |
|
| GP1pin 11 | Connected to: Signal 69% · not connected 31% |
|
| VDDpin 18 | Connected to: 5V 69% · a signal 23% | — |
| Pin 20 | Connected to: 3.3V 75% · a signal 25% |
|
9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include HL2 Filter Board by softerhardware, Filter by profdc9, Radioberry LPF V1.3 by pa3gsb and PiPtr by jmlzone.
The MCP23008 in open source designs
The gallery holds 18 open source boards using the MCP23008 from 13 GitHub repositories; a typical one measures about 100 × 96.3 mm and carries around 86 components.
82% are two-layer designs, the rest use four layers or more, and 28% carry an open source license.
The most starred is HL2 Filter Board by softerhardware.
Parts used alongside the MCP23008
Microcontrollers on boards using the MCP23008
What boards using the MCP23008 are built for
MCP23008: common questions
Where can I find a MCP23008 reference design?
Each of the 18 boards on this page is a real design using the MCP23008. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP23008 INT pin connected?
The INT pin is left unconnected on 12 of 13 designs. Counted from the KiCad layouts of 13 open source designs using the MCP23008.
What pull-up resistor is used on the MCP23008 SCL pin?
The SCL pin has a pull-up to 5V on 7 of 13 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 13 open source designs using the MCP23008.
What pull-up resistor is used on the MCP23008 SDA pin?
The SDA pin has a pull-up to 5V on 7 of 13 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 13 open source designs using the MCP23008.
Which microcontrollers do boards using the MCP23008 use?
Most are built on ESP8266 (4), AVR/Arduino (2), FPGA (1) and NXP (1).
How big is a typical board using the MCP23008?
The median is 100 × 96.3 mm, and 82% are two-layer designs.
What is the most popular open source board using the MCP23008?
By GitHub stars, HL2 Filter Board by softerhardware, with 372 stars.
Can I simulate one of these boards using the MCP23008 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.