17 open source boards using the MCP2562-E-MF

Real designs built with the MCP2562-E-MF, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

17 boardsClear filters|Most starred

How designs wire the MCP2562-E-MF

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MCP2562-E-MF connects to, and the resistors, capacitors and other passives placed on it.

  • The PAD_9 pin is tied to GND on 5 of 5 designs.
  • The VDD_3 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
  • The CANL_6 pin has a series resistor on 4 of 5 designs, most often 120 Ω.
  • The SHDN_8 pin is tied to GND on 4 of 5 designs.
VSS_2pin 2Connected to: GND 100%
VDD_3pin 3Connected to: 5V 100%
  • Decoupling capacitor on 80% · 100 nF (4)
VIO_5pin 5Connected to: 3.3V 100%
  • Decoupling capacitor on 60% · 100 nF (3)
CANL_6pin 6Connected to: A connector 100%
  • Series resistor on 80% · 120 Ω (4)
SHDN_8pin 8Connected to: GND 80% · a signal 20%
PAD_9pin 9Connected to: GND 100%

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include WPT TX by mark-belbin, Obd32 by mkrasselt1, Robust io.before align by lusher00 and Jetson interface board by tmcit-ararobo-2026a.

The MCP2562-E-MF in open source designs

The gallery holds 17 open source boards using the MCP2562-E-MF from 5 GitHub repositories; a typical one measures about 160 × 100 mm and carries around 259 components.

76% use four copper layers or more, and 12% carry an open source license.

The most starred is WPT TX by mark-belbin.

Microcontrollers on boards using the MCP2562-E-MF

What boards using the MCP2562-E-MF are built for

MCP2562-E-MF: common questions

Where can I find a MCP2562-E-MF reference design?

Each of the 17 boards on this page is a real design using the MCP2562-E-MF. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MCP2562-E-MF PAD_9 pin connected?

The PAD_9 pin is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MCP2562-E-MF.

What decoupling capacitors do designs use on the MCP2562-E-MF VDD_3 pin?

The VDD_3 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the MCP2562-E-MF.

What resistor goes on the MCP2562-E-MF CANL_6 pin?

The CANL_6 pin has a series resistor on 4 of 5 designs, most often 120 Ω. Counted from the KiCad layouts of 5 open source designs using the MCP2562-E-MF.

Which microcontrollers do boards using the MCP2562-E-MF use?

Most are built on AVR/Arduino (12), STM32 (2), ESP32 (1) and Microchip SAM (1).

How big is a typical board using the MCP2562-E-MF?

The median is 160 × 100 mm, and 24% are two-layer designs.

What is the most popular open source board using the MCP2562-E-MF?

By GitHub stars, WPT TX by mark-belbin, with 73 stars.

Can I simulate one of these boards using the MCP2562-E-MF before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part