7 open source boards using the MCP41010
Real designs built with the MCP41010, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
SmartSupply
ThomasVDD
169.3 × 128 mm131 parts2LCustom license96AVR/Arduino
PSU
ThomasVDD
50 × 100 mm116 parts2LCustom license16STM32
ArmLabRadio
explosion33
57.2 × 57.2 mm90 parts2LNo license4AVR/Arduino
Switch Panel
Plasmarobo
118.1 × 80 mm55 parts2LCC-BY-NC-4.01Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487AVR/Arduino
Enc panel
mar0x
68.6 × 89.5 mm30 parts2LNo license0Disarmed
Plasmarobo
170.2 × 180.3 mm15 parts4LCC-BY-NC-4.01
How designs wire the MCP41010
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MCP41010 connects to, and the resistors, capacitors and other passives placed on it.
- The PA0 pin has a series resistor on 3 of 6 designs, most often 10 kΩ (then 1.5 MΩ).
- The VDD pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 1 | Connected to: The microcontroller 50% |
|
| VSSpin 4 | Connected to: GND 100% | — |
| PA0pin 5 | Connected to: LT1370 33% · not connected 17% · 3.3V 33% |
|
| PW0pin 6 | Connected to: Signal 83% · not connected 17% |
|
| VDDpin 8 | Connected to: 5V 100% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OpenDropV4 by GaudiLabs, SmartSupply by ThomasVDD, PSU PCB by ThomasVDD and ArmLabRadio PCB by explosion33.
The MCP41010 in open source designs
The gallery holds 7 open source boards using the MCP41010 from 6 GitHub repositories; a typical one measures about 118.1 × 100 mm and carries around 90 components.
86% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.
The most starred is OpenDropV4 by GaudiLabs.
Microcontrollers on boards using the MCP41010
What boards using the MCP41010 are built for
MCP41010: common questions
Where can I find a MCP41010 reference design?
Each of the 7 boards on this page is a real design using the MCP41010. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP41010 PA0 pin?
The PA0 pin has a series resistor on 3 of 6 designs, most often 10 kΩ (then 1.5 MΩ). Counted from the KiCad layouts of 6 open source designs using the MCP41010.
What decoupling capacitors do designs use on the MCP41010 VDD pin?
The VDD pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the MCP41010.
What parts are used alongside the MCP41010?
The 74HC595, INA219, LT1370 and LT3080 appear in the most repositories here.
Which microcontrollers do boards using the MCP41010 use?
Most are built on AVR/Arduino (4), Microchip SAM (1) and STM32 (1).
How big is a typical board using the MCP41010?
The median is 118.1 × 100 mm, and 86% are two-layer designs.
What is the most popular open source board using the MCP41010?
By GitHub stars, OpenDropV4 by GaudiLabs, with 487 stars.
Can I simulate one of these boards using the MCP41010 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.