9 open source boards using the MCP73831-3-OT

Real designs built with the MCP73831-3-OT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the MCP73831-3-OT

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MCP73831-3-OT connects to, and the resistors, capacitors and other passives placed on it.

  • The PROG pin has a resistor to GND on 6 of 6 designs, most often 2 kΩ (then 4.7 kΩ).
  • The STAT pin has a series resistor on 5 of 6 designs, most often 1 kΩ (then 100 Ω).
  • The VBAT pin has a decoupling capacitor on 4 of 6 designs, most often 10 µF (then 4.7 µF).
  • The VDD pin has a decoupling capacitor on 4 of 6 designs, most often 4.7 µF (then 100 nF).
STATpin 1Connected to: Signal 100%
  • Series resistor on 83% · 1 kΩ (2), 100 Ω (1), 330 Ω (1)
VSSpin 2Connected to: GND 100%
VBATpin 3Connected to: BATT 100%
  • Decoupling capacitor on 67% · 10 µF (3), 4.7 µF (1)
VDDpin 4Connected to: VBUS 100%
  • Decoupling capacitor on 67% · 4.7 µF (2), 100 nF (1), 10 µF (1)
PROGpin 5Connected to: Signal 100%
  • Resistor to GND on 100% · 2 kΩ (2), 4.7 kΩ (1), 100 Ω (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hunter Cat NFC by ElectronicCats, Base by rmingon, BastWiFi by ElectronicCats and Gps animal by ElectronicCats.

The MCP73831-3-OT in open source designs

The gallery holds 9 open source boards using the MCP73831-3-OT from 6 GitHub repositories; a typical one measures about 71.1 × 42.7 mm and carries around 53 components.

78% are two-layer designs, the rest use four layers or more, and 11% carry an open source license.

The most starred is Hunter Cat NFC by ElectronicCats.

Parts used alongside the MCP73831-3-OT

Microcontrollers on boards using the MCP73831-3-OT

MCP73831-3-OT: common questions

Where can I find a MCP73831-3-OT reference design?

Each of the 9 boards on this page is a real design using the MCP73831-3-OT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the MCP73831-3-OT PROG pin?

The PROG pin has a resistor to GND on 6 of 6 designs, most often 2 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the MCP73831-3-OT.

What resistor goes on the MCP73831-3-OT STAT pin?

The STAT pin has a series resistor on 5 of 6 designs, most often 1 kΩ (then 100 Ω). Counted from the KiCad layouts of 6 open source designs using the MCP73831-3-OT.

What decoupling capacitors do designs use on the MCP73831-3-OT VBAT pin?

The VBAT pin has a decoupling capacitor on 4 of 6 designs, most often 10 µF (then 4.7 µF). Counted from the KiCad layouts of 6 open source designs using the MCP73831-3-OT.

Which microcontrollers do boards using the MCP73831-3-OT use?

Most are built on ESP32 (3), Microchip SAM (3), STM32 (2) and RP2040/RP2350 (1).

How big is a typical board using the MCP73831-3-OT?

The median is 71.1 × 42.7 mm, and 78% are two-layer designs.

What is the most popular open source board using the MCP73831-3-OT?

By GitHub stars, Hunter Cat NFC by ElectronicCats, with 233 stars.

Can I simulate one of these boards using the MCP73831-3-OT before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part