6 open source boards using the MIC5504
Real designs built with the MIC5504, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
Keyboard
ataradov
348.4 × 110.2 mm252 parts2LBSD-3-Clause1STM32
C152ThrottleQuadrant
bkryza
140 × 85 mm62 parts2LNo license1STM32
HoHo
i2cjak
25 × 25 mm56 parts4LCERN-OHL-P-2.00- schematic only · 93 partsESP32
GuavaPI
SebRincon
93 partsNo license0 Nordic nRF
Revolute production
tongtongwang86
19.9 × 19.5 mm59 parts4LCC-BY-NC-4.05STM32
Proc stm32
M-o-a-T
28 × 15.5 mm18 parts2LNo license0
How designs wire the MIC5504
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MIC5504 connects to, and the resistors, capacitors and other passives placed on it.
- The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 1 µF.
- The EN pin is tied to 5V on 4 of 5 designs.
- The VOUT pin has a decoupling capacitor on 3 of 5 designs, most often 1 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: 5V 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| ENpin 3 | Connected to: 5V 80% · a signal 20% | — |
| NCpin 4 | Connected to: Not connected 80% · a signal 20% | — |
| VOUTpin 5 | Connected to: 3.3V 80% · GND 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Revolute production by tongtongwang86, Keyboard by ataradov, C152ThrottleQuadrant by bkryza and HoHo by i2cjak.
The MIC5504 in open source designs
The gallery holds 6 open source boards using the MIC5504 from 6 GitHub repositories; a typical one measures about 28 × 25 mm and carries around 61 components.
60% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Revolute production by tongtongwang86.
Microcontrollers on boards using the MIC5504
What boards using the MIC5504 are built for
MIC5504: common questions
Where can I find a MIC5504 reference design?
Each of the 6 boards on this page is a real design using the MIC5504. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MIC5504 VIN pin?
The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 1 µF. Counted from the KiCad layouts of 5 open source designs using the MIC5504.
How is the MIC5504 EN pin connected?
The EN pin is tied to 5V on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MIC5504.
What decoupling capacitors do designs use on the MIC5504 VOUT pin?
The VOUT pin has a decoupling capacitor on 3 of 5 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the MIC5504.
Which microcontrollers do boards using the MIC5504 use?
Most are built on STM32 (3), ESP32 (1), Nordic nRF (1) and Microchip SAM (1).
How big is a typical board using the MIC5504?
The median is 28 × 25 mm, and 60% are two-layer designs.
What is the most popular open source board using the MIC5504?
By GitHub stars, Revolute production by tongtongwang86, with 5 stars.
Can I simulate one of these boards using the MIC5504 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.