8 open source boards using the MS5611
Real designs built with the MS5611, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
SimpleFC G
wangyeee
42 × 50 mm130 parts4LBSD-3-Clause9STM32
Draco
xdandys
47.5 × 62 mm173 parts4LNo license8STM32
Iridium drone
kfilipekk
45 × 47.2 mm168 parts6LNo license0RP2040/RP2350
Hub board v1
felixfelix-bot
50 × 40 mm21 parts2LNo license0ESP32
ENV-sensor esp32
bruvv
55 × 70 mm9 parts4LGPL-3.00STM32
SimpleFCv2
wangyeee
42 × 50 mm119 parts4LBSD-3-Clause9RP2040/RP2350
Hub board f33
felixfelix-bot
75 × 55 mm12 parts2LNo license0STM32
AirSeneor
wangyeee
45 × 30 mm39 parts2LBSD-3-Clause9
How designs wire the MS5611
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MS5611 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC_1 pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF.
- The SCL_3 pin is tied to GND on 3 of 5 designs (a signal on 2).
- The SDA_4 pin has a pull-up to 3.3V on 2 of 5 designs, most often 39 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCC_1pin 1 | Connected to: 3.3V 100% |
|
| GND_2pin 2 | Connected to: GND 80% · 3.3V 20% | — |
| SCL_3pin 3 | Connected to: GND 60% · a signal 40% | — |
| SDA_4pin 4 | Connected to: The microcontroller 40% · GND 20% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AirSeneor by wangyeee, Draco by xdandys, ENV-sensor esp32 by bruvv and Hub board f33 by felixfelix-bot.
The MS5611 in open source designs
The gallery holds 8 open source boards using the MS5611 from 5 GitHub repositories; a typical one measures about 46.3 × 50 mm and carries around 79 components.
63% use four copper layers or more, and 50% carry an open source license.
The most starred is SimpleFC G by wangyeee.
Microcontrollers on boards using the MS5611
What boards using the MS5611 are built for
MS5611: common questions
Where can I find a MS5611 reference design?
Each of the 8 boards on this page is a real design using the MS5611. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MS5611 VCC_1 pin?
The VCC_1 pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the MS5611.
How is the MS5611 SCL_3 pin connected?
The SCL_3 pin is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the MS5611.
What pull-up resistor is used on the MS5611 SDA_4 pin?
The SDA_4 pin has a pull-up to 3.3V on 2 of 5 designs, most often 39 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the MS5611.
Which microcontrollers do boards using the MS5611 use?
Most are built on STM32 (5), RP2040/RP2350 (2) and ESP32 (1).
How big is a typical board using the MS5611?
The median is 46.3 × 50 mm, and 38% are two-layer designs.
What is the most popular open source board using the MS5611?
By GitHub stars, SimpleFC G by wangyeee, with 9 stars.
Can I simulate one of these boards using the MS5611 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.