7 open source boards using the NEO-M8N
Real designs built with the NEO-M8N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
NXP
Harness tester challenge
commaai
61 × 71 mm25 parts4LMIT119U blox gnss receiver
lpechacek
65.4 × 41.9 mm41 parts2LCC-BY-4.014ESP32
Alcantara
zenitheesc
101.5 × 43.6 mm88 parts4LNo license5STM32
Ollyfc
rland93
45 × 98 mm101 parts4LMPL-2.02ESP32
ESP32 Offline GPS MAPS
uzzambutt
75 × 130 mm67 parts4LNo license1ESP32
Mesh rack
sneakylizard123-4
200 × 100 mm74 parts4LNo license0STM32
Vehicle movement parameters
Iverson-45
79 × 75 mm54 parts2LNo license0
How designs wire the NEO-M8N
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the NEO-M8N connects to, and the resistors, capacitors and other passives placed on it.
- The LNA_EN pin is left unconnected on 7 of 7 designs.
- The RESERVED pins is left unconnected on 100% of them.
- The SAFEBOOT pin is left unconnected on 6 of 7 designs.
- The SDA/SPI_CS pin is left unconnected on 6 of 7 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SAFEBOOTpin 1 | Connected to: Not connected 86% | — |
| D_SELpin 2 | Connected to: Not connected 71% | — |
| EXTINTpin 4 | Connected to: Not connected 71% · a signal 29% | — |
| USB_DMpin 5 | Connected to: Not connected 71% · a signal 29% | — |
| USB_DPpin 6 | Connected to: Not connected 71% · a signal 29% | — |
| GNDpin 10, 12, 13, 24 | Connected to: GND 86% | — |
| RF_INpin 11 | Connected to: A connector 43% |
|
| LNA_ENpin 14 | Connected to: Not connected 100% | — |
| RESERVEDpin 15, 16, 17 | Connected to: Not connected 100% | — |
| SDA/SPI_CSpin 18 | Connected to: Not connected 86% | — |
| SCL/SPI_CLKpin 19 | Connected to: Not connected 86% | — |
| V_BCKPpin 22 | Connected to: 3.3V 57% · a signal 43% |
|
| VCCpin 23 | Connected to: 3.3V 100% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Harness tester challenge by commaai, U blox gnss receiver by lpechacek, Alcantara by zenitheesc and Ollyfc by rland93.
The NEO-M8N in open source designs
The gallery holds 7 open source boards using the NEO-M8N from 7 GitHub repositories; a typical one measures about 75 × 75 mm and carries around 67 components.
71% use four copper layers or more, and 43% carry an open source license.
The most starred is Harness tester challenge by commaai.
Parts used alongside the NEO-M8N
What boards using the NEO-M8N are built for
NEO-M8N: common questions
Where can I find a NEO-M8N reference design?
Each of the 7 boards on this page is a real design using the NEO-M8N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the NEO-M8N LNA_EN pin connected?
The LNA_EN pin is left unconnected on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the NEO-M8N.
How is the NEO-M8N RESERVED pin connected?
The RESERVED pins is left unconnected on 100% of them. Counted from the KiCad layouts of 7 open source designs using the NEO-M8N.
How is the NEO-M8N SAFEBOOT pin connected?
The SAFEBOOT pin is left unconnected on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the NEO-M8N.
Which microcontrollers do boards using the NEO-M8N use?
Most are built on ESP32 (3), STM32 (2) and NXP (1).
How big is a typical board using the NEO-M8N?
The median is 75 × 75 mm, and 29% are two-layer designs.
What is the most popular open source board using the NEO-M8N?
By GitHub stars, Harness tester challenge by commaai, with 119 stars.
Can I simulate one of these boards using the NEO-M8N before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.