18 open source boards using the NJM4580
Real designs built with the NJM4580, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Main-Board
open-headset-interconnect-standard
100 × 84 mm146 parts2LCC-BY-4.05ESP32
Gifu Creation Koubou Teaching Material
kinoshita-lab
210 × 140 mm109 parts2LMIT3RP2040/RP2350
Pico-SMSFM
knight-ryu12
76.1 × 64.1 mm31 parts2LNo license1- schematic only · 44 parts
KiCad-Simulation
46nori
44 partsNo license0 V1000
Tert2
72 × 47.5 mm69 parts2LNo license0RP2040/RP2350
SystemController
46nori
180 × 81.3 mm63 parts4LMIT0IPM-165 amplifier circuit
KakuheikiCreator
50.8 × 50.8 mm33 parts2LMIT0AND8bit
Tert2
100 × 100 mm61 parts2LNo license0ESP32
ESP32S3
Tert2
27.9 × 57.2 mm48 parts4LNo license0BDoperator
kanengomibako
54 × 47 mm61 parts2LUnlicense11AVR/Arduino
Ammeter
Tert2
25 × 15 mm45 parts4LNo license0ESP32
C3 men
Tert2
86 × 89 mm30 parts2LNo license0Mother UI
Tomoshibi-technology
100 × 60 mm92 parts2LMIT1AVR/Arduino
Jogi
Tert2
100 × 99 mm24 parts2LNo license0ConsistentGuitarOutput RevA
kanengomibako
94 × 59 mm38 parts2LUnlicense11AVR/Arduino
ATMEGA328P
Tert2
36 × 37.5 mm17 parts4LNo license0Ws2811
Tert2
83 × 100 mm15 parts2LNo license0AVR/Arduino
ATtiny
Tert2
86 × 77 mm11 parts2LNo license0
How designs wire the NJM4580
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the NJM4580 connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 7 of 8 designs, most often 10 kΩ (then 470 kΩ).
- The +_1 pin has a series resistor on 6 of 8 designs, most often 10 kΩ (then 470 kΩ).
- Pin 7 has a series resistor on 6 of 7 designs, most often 33 kΩ (then 10 kΩ).
- The V- pin is tied to GND on 7 of 8 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| +_1pin 1 | Connected to: Signal 88% |
|
| -pin 2, 6 | Connected to: Signal 80% |
|
| +pin 3, 5 | Connected to: Signal 81% |
|
| V-pin 4 | Connected to: GND 88% | — |
| Pin 7 | Connected to: Signal 86% |
|
| V+pin 8 | Connected to: VCC 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BDoperator by kanengomibako, Main-Board by open-headset-interconnect-standard, Gifu Creation Koubou Teaching Material by kinoshita-lab and Pico-SMSFM by knight-ryu12.
The NJM4580 in open source designs
The gallery holds 18 open source boards using the NJM4580 from 9 GitHub repositories; a typical one measures about 86 × 64.1 mm and carries around 45 components.
76% are two-layer designs, the rest use four layers or more, and 39% carry an open source license.
The most starred is BDoperator by kanengomibako.
Microcontrollers on boards using the NJM4580
What boards using the NJM4580 are built for
NJM4580: common questions
Where can I find a NJM4580 reference design?
Each of the 18 boards on this page is a real design using the NJM4580. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the NJM4580 - pin?
The - pins have a series resistor on 7 of 8 designs, most often 10 kΩ (then 470 kΩ). Counted from the KiCad layouts of 8 open source designs using the NJM4580.
What resistor goes on the NJM4580 +_1 pin?
The +_1 pin has a series resistor on 6 of 8 designs, most often 10 kΩ (then 470 kΩ). Counted from the KiCad layouts of 8 open source designs using the NJM4580.
What resistor goes on the NJM4580 pin 7?
Pin 7 has a series resistor on 6 of 7 designs, most often 33 kΩ (then 10 kΩ). Counted from the KiCad layouts of 8 open source designs using the NJM4580.
Which microcontrollers do boards using the NJM4580 use?
Most are built on AVR/Arduino (4), ESP32 (3) and RP2040/RP2350 (2).
How big is a typical board using the NJM4580?
The median is 86 × 64.1 mm, and 76% are two-layer designs.
What is the most popular open source board using the NJM4580?
By GitHub stars, BDoperator by kanengomibako, with 11 stars.
Can I simulate one of these boards using the NJM4580 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.