11 open source boards using the NodeMCU_1.0_(ESP-12E)

Real designs built with the NodeMCU_1.0_(ESP-12E), from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

11 boardsClear filters|Most starred

How designs wire the NodeMCU_1.0_(ESP-12E)

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the NodeMCU_1.0_(ESP-12E) connects to, and the resistors, capacitors and other passives placed on it.

  • The RSV pins is left unconnected on 100% of them.
  • The SD3(GPIO10) pin is left unconnected on 6 of 6 designs.
  • The SD2(GPIO9) pin is left unconnected on 6 of 6 designs.
  • The EN pin is left unconnected on 6 of 6 designs.
A0(ADC0)pin 1Connected to: Not connected 67% · a signal 33%
RSVpin 2, 3Connected to: Not connected 100%
SD3(GPIO10)pin 4Connected to: Not connected 100%
SD2(GPIO9)pin 5Connected to: Not connected 100%
SD1(MOSI)pin 6Connected to: Not connected 83% · a signal 17%
CMD(CS)pin 7Connected to: Not connected 83% · a signal 17%
SDO(MISO)pin 8Connected to: Not connected 83% · a signal 17%
CLK(SCLK)pin 9Connected to: Not connected 83% · a signal 17%
GNDpin 10, 14, 17, 24Connected to: GND 92%
3.3Vpin 11, 16, 25Connected to: 3.3V 67% · not connected 28%
ENpin 12Connected to: Not connected 100%
VINpin 15Connected to: 5V 83% · not connected 17%
TX(GPIO1)pin 18Connected to: Not connected 67% · a signal 33%
RX(DPIO3)pin 19Connected to: Not connected 67% · a signal 33%
D7(GPIO13)pin 21Connected to: Signal 67% · not connected 33%
  • Series resistor on 33% · 47 Ω (1), 5.6 kΩ (1), 22 Ω (1)

9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Rgbw 12v controller by SmartHome-yourself, Esp8266-io board by tute-avalos, NodeMCU-Metriful by axello and Board withoutEncoder by DaniMzT.

The NodeMCU_1.0_(ESP-12E) in open source designs

The gallery holds 11 open source boards using the NodeMCU_1.0_(ESP-12E) from 6 GitHub repositories; a typical one measures about 90 × 68.6 mm and carries around 21 components.

100% are two-layer designs, the rest use four layers or more, and 45% carry an open source license.

The most starred is Rgbw 12v controller by SmartHome-yourself.

Microcontrollers on boards using the NodeMCU_1.0_(ESP-12E)

What boards using the NodeMCU_1.0_(ESP-12E) are built for

NodeMCU_1.0_(ESP-12E): common questions

Where can I find a NodeMCU_1.0_(ESP-12E) reference design?

Each of the 11 boards on this page is a real design using the NodeMCU_1.0_(ESP-12E). Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the NodeMCU_1.0_(ESP-12E) RSV pin connected?

The RSV pins is left unconnected on 100% of them. Counted from the KiCad layouts of 6 open source designs using the NodeMCU_1.0_(ESP-12E).

How is the NodeMCU_1.0_(ESP-12E) SD3(GPIO10) pin connected?

The SD3(GPIO10) pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the NodeMCU_1.0_(ESP-12E).

How is the NodeMCU_1.0_(ESP-12E) SD2(GPIO9) pin connected?

The SD2(GPIO9) pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the NodeMCU_1.0_(ESP-12E).

Which microcontrollers do boards using the NodeMCU_1.0_(ESP-12E) use?

Most are built on ESP8266 (11).

How big is a typical board using the NodeMCU_1.0_(ESP-12E)?

The median is 90 × 68.6 mm, and 100% are two-layer designs.

What is the most popular open source board using the NodeMCU_1.0_(ESP-12E)?

By GitHub stars, Rgbw 12v controller by SmartHome-yourself, with 6 stars.

Can I simulate one of these boards using the NodeMCU_1.0_(ESP-12E) before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part