8 open source boards using the OPA320
Real designs built with the OPA320, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Glove v4-routing candidate
latintzar
100 × 80 mm561 parts8LMIT0FPGA
AL-MAWJA
m0-hassan
194 parts4LNo license0STM32
UPSat COMMS
Ki365
92.5 × 92.5 mm190 parts4LCERN-OHL-1.20STM32
UPSat COMMS
mcgillspace
92.5 × 92.5 mm190 parts4LCERN-OHL-1.20STM32
UPSat COMMS
npe9
92.5 × 92.5 mm190 parts4LCERN-OHL-1.20ESP32
Glove v4-placement
latintzar
100 × 80 mm560 parts6LMIT0STM32
IR Controller v2
TIGERs-Mannheim
90 × 41 mm107 parts2LCustom license9Ball Detection v4
TIGERs-Mannheim
10 × 51 mm9 parts2LCustom license9
How designs wire the OPA320
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the OPA320 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 6 of 6 designs, most often 1 MΩ (then 22 Ω).
- The -_4 pin has a series resistor on 6 of 6 designs, most often 1 MΩ (then 22 Ω).
- The V+_5 pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 330 pF).
- The V-_2 pin is tied to GND on 6 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| V-_2pin 2 | Connected to: GND 100% | — |
| -_4pin 4 | Connected to: Signal 100% |
|
| V+_5pin 5 | Connected to: 3.3V 83% · a signal 17% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ball Detection v4 by TIGERs-Mannheim, UPSat COMMS by Ki365, Glove v4-placement by latintzar and AL-MAWJA by m0-hassan.
The OPA320 in open source designs
The gallery holds 8 open source boards using the OPA320 from 6 GitHub repositories; a typical one measures about 92.5 × 80 mm and carries around 190 components.
75% use four copper layers or more, and 63% carry an open source license.
The most starred is IR Controller v2 by TIGERs-Mannheim.
Parts used alongside the OPA320
What boards using the OPA320 are built for
OPA320: common questions
Where can I find a OPA320 reference design?
Each of the 8 boards on this page is a real design using the OPA320. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the OPA320 pin 1?
Pin 1 has a series resistor on 6 of 6 designs, most often 1 MΩ (then 22 Ω). Counted from the KiCad layouts of 6 open source designs using the OPA320.
What resistor goes on the OPA320 -_4 pin?
The -_4 pin has a series resistor on 6 of 6 designs, most often 1 MΩ (then 22 Ω). Counted from the KiCad layouts of 6 open source designs using the OPA320.
What decoupling capacitors do designs use on the OPA320 V+_5 pin?
The V+_5 pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 330 pF). Counted from the KiCad layouts of 6 open source designs using the OPA320.
What parts are used alongside the OPA320?
The ADT7420, CC1120, FA_128_, RF5110G and STM32F407VG appear in the most repositories here.
Which microcontrollers do boards using the OPA320 use?
Most are built on STM32 (4), ESP32 (2) and FPGA (1).
How big is a typical board using the OPA320?
The median is 92.5 × 80 mm, and 25% are two-layer designs.
What is the most popular open source board using the OPA320?
By GitHub stars, IR Controller v2 by TIGERs-Mannheim, with 9 stars.
Can I simulate one of these boards using the OPA320 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.