10 open source boards using the PAM8302AAS

Real designs built with the PAM8302AAS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

10 boardsClear filters|Most starred

How designs wire the PAM8302AAS

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the PAM8302AAS connects to, and the resistors, capacitors and other passives placed on it.

  • The VDD pin has a decoupling capacitor on 8 of 9 designs, most often 10 µF (then 1 µF).
  • The IN+ pin has a series resistor on 5 of 9 designs, most often 100 Ω (then 80 kΩ).
  • The IN- pin has a series resistor on 5 of 9 designs, most often 100 Ω (then 80 kΩ).
  • The SD pin has a resistor to GND on 4 of 9 designs, most often 10 kΩ (then 1 kΩ).
SDpin 1Connected to: The microcontroller 22%
  • Resistor to GND on 44% · 10 kΩ (2), 1 kΩ (1), 100 kΩ (1)
  • Pull-up to 5V on 33% · 10 kΩ (3)
NCpin 2Connected to: Not connected 100%
IN+pin 3Connected to: Signal 100%
  • Series resistor on 56% · 100 Ω (4), 80 kΩ (1)
IN-pin 4Connected to: Signal 89%
  • Series resistor on 56% · 100 Ω (4), 80 kΩ (1)
OUT+pin 5Connected to: A connector 56%
  • Ferrite bead on 33%
VDDpin 6Connected to: 5V 89%
  • Decoupling capacitor on 89% · 10 µF (6), 1 µF (3), 100 nF (2)
GNDpin 7Connected to: GND 100%
OUT-pin 8Connected to: A connector 44%
  • Ferrite bead on 33%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Gk by jncronin, Gameboy dmg pcb by alxhoff, Starman by adamm and Hoppy clock by borkdlabs.

The PAM8302AAS in open source designs

The gallery holds 10 open source boards using the PAM8302AAS from 9 GitHub repositories; a typical one measures about 64.5 × 55.5 mm and carries around 51 components.

50% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.

The most starred is Gk pcbv3 by jncronin.

Microcontrollers on boards using the PAM8302AAS

PAM8302AAS: common questions

Where can I find a PAM8302AAS reference design?

Each of the 10 boards on this page is a real design using the PAM8302AAS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the PAM8302AAS VDD pin?

The VDD pin has a decoupling capacitor on 8 of 9 designs, most often 10 µF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the PAM8302AAS.

What resistor goes on the PAM8302AAS IN+ pin?

The IN+ pin has a series resistor on 5 of 9 designs, most often 100 Ω (then 80 kΩ). Counted from the KiCad layouts of 9 open source designs using the PAM8302AAS.

What resistor goes on the PAM8302AAS IN- pin?

The IN- pin has a series resistor on 5 of 9 designs, most often 100 Ω (then 80 kΩ). Counted from the KiCad layouts of 9 open source designs using the PAM8302AAS.

Which microcontrollers do boards using the PAM8302AAS use?

Most are built on STM32 (5), AVR/Arduino (1), ESP32 (1) and Raspberry Pi (1).

How big is a typical board using the PAM8302AAS?

The median is 64.5 × 55.5 mm, and 50% are two-layer designs.

What is the most popular open source board using the PAM8302AAS?

By GitHub stars, Gk pcbv3 by jncronin, with 78 stars.

Can I simulate one of these boards using the PAM8302AAS before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part