7 open source boards using the PCA9306D
Real designs built with the PCA9306D, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Ulx3s
emard
94 × 50.8 mm212 parts4LMIT470ESP32
Mini power
hnz1102
46 × 54 mm49 parts2LNo license3RP2040/RP2350
Battery powered
homelith
56 × 71.5 mm59 parts4LMIT2ESP32
Dcpower
hnz1102
58 × 90 mm101 parts2LNo license1Pca9306-i2c level shifter
embedrapp
60 × 40 mm10 parts2LMIT1ESP32
Remote omnidirection droid v0.1
eloicote
120 × 103.9 mm79 parts2LGPL-3.00STM32
Pcb nixie
fernandezdelpeloso
90.7 × 90.7 mm44 parts6LNo license0
How designs wire the PCA9306D
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the PCA9306D connects to, and the resistors, capacitors and other passives placed on it.
- The SCL1 pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 3.3 kΩ).
- The SDA2 pin has a pull-up to 5V on 7 of 7 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL2 pin has a pull-up to 5V on 7 of 7 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA1 pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ (then 3.3 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 86% | — |
| VREF1pin 2 | Connected to: 3.3V 100% |
|
| SCL1pin 3 | Connected to: The microcontroller 71% |
|
| SDA1pin 4 | Connected to: The microcontroller 86% |
|
| SDA2pin 5 | Connected to: A connector 43%, AP33772SDKZ-13-FA01 29% |
|
| SCL2pin 6 | Connected to: A connector 43%, AP33772SDKZ-13-FA01 29% |
|
| VREF2pin 7 | Connected to: 5V 71% · a signal 29% | — |
| ENpin 8 | Connected to: Signal 57% · 5V 43% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ulx3s by emard, Mini power by hnz1102, Battery powered by homelith and Pca9306-i2c level shifter by embedrapp.
The PCA9306D in open source designs
The gallery holds 7 open source boards using the PCA9306D from 7 GitHub repositories; a typical one measures about 60 × 71.5 mm and carries around 59 components.
57% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is Ulx3s by emard.
Parts used alongside the PCA9306D
Microcontrollers on boards using the PCA9306D
What boards using the PCA9306D are built for
PCA9306D: common questions
Where can I find a PCA9306D reference design?
Each of the 7 boards on this page is a real design using the PCA9306D. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the PCA9306D SCL1 pin?
The SCL1 pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 7 open source designs using the PCA9306D.
What pull-up resistor is used on the PCA9306D SDA2 pin?
The SDA2 pin has a pull-up to 5V on 7 of 7 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the PCA9306D.
What pull-up resistor is used on the PCA9306D SCL2 pin?
The SCL2 pin has a pull-up to 5V on 7 of 7 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the PCA9306D.
Which microcontrollers do boards using the PCA9306D use?
Most are built on ESP32 (4), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the PCA9306D?
The median is 60 × 71.5 mm, and 57% are two-layer designs.
What is the most popular open source board using the PCA9306D?
By GitHub stars, Ulx3s by emard, with 470 stars.
Can I simulate one of these boards using the PCA9306D before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.