8 open source boards using the POWERSTEP01
Real designs built with the POWERSTEP01, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Wifistepper
goodrobotics
77.6 × 57.3 mm85 parts4LNo license29FPGA
Keep breathing ctrl
CV19CO
153 × 148 mm248 parts4LCERN-OHL-P-2.05STM32
OtterStepMini
Jana-Marie
68.4 × 50 mm63 parts4LNo license5Powerstep01-breakout
goodrobotics
65.3 × 52.8 mm24 parts2LNo license29Pressure sensors
CV19CO
100 × 100 mm10 parts4LCERN-OHL-P-2.05Powerstep
rene-dev
95.2 × 71.5 mm28 parts4LGPL-3.0979Powerstep
emdotnet
95.2 × 71.5 mm28 parts4LGPL-3.00PaP
brengi
60 × 60 mm58 parts2LNo license7
How designs wire the POWERSTEP01
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the POWERSTEP01 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 57 has a series capacitor on 6 of 6 designs, most often 47 nF (then 220 nF).
- Pin 9 has a resistor to GND on 5 of 6 designs, most often 270 mΩ (then 100 mΩ).
- Pin 20 has a resistor to GND on 5 of 6 designs, most often 270 mΩ (then 100 mΩ).
- Pin 54 has a resistor to GND on 5 of 6 designs, most often 1.8 kΩ (then 5.1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: A connector 50% |
|
| Pin 8 | Connected to: GND 83% · a signal 17% | — |
| Pin 9 | Connected to: Signal 100% |
|
| Pin 10 | Connected to: POWERSTEP01 33%, the microcontroller 33% |
|
| Pin 13 | Connected to: 3.3V 50% · a signal 50% |
|
| Pin 14 | Connected to: POWERSTEP01 33%, the microcontroller 33% |
|
| Pin 15 | Connected to: Signal 67% · not connected 33% |
|
| Pin 16 | Connected to: Signal 67% · not connected 33% |
|
| Pin 18 | Connected to: Not connected 50% · a signal 50% |
|
| Pin 19 | Connected to: POWERSTEP01 33%, the microcontroller 33% |
|
| Pin 20 | Connected to: Signal 100% |
|
| Pin 23 | Connected to: Not connected 50% · a signal 50% |
|
| Pin 34 | Connected to: Signal 100% |
|
| Pin 39 | Connected to: Not connected 50% · a signal 50% |
|
| Pin 43 | Connected to: Not connected 40% · 85V 20% · a signal 40% |
|
| Pin 54 | Connected to: Signal 100% |
|
| Pin 55 | Connected to: Not connected 33% · VIN 33% · a signal 33% |
|
| Pin 56 | Connected to: Signal 100% |
|
| Pin 57 | Connected to: Signal 100% |
|
| Pin 58 | Connected to: Signal 83% · 15V 17% |
|
| Pin 60 | Connected to: 3.3V 50% · a signal 50% |
|
| Pin 61 | Connected to: A connector 33% · VIN 33% |
|
| Pin 62 | Connected to: 3.3V 50% · a signal 50% |
|
| Pin 63 | Connected to: Not connected 83% · a signal 17% | — |
| Pin 64 | Connected to: Not connected 83% · a signal 17% | — |
| Pin 66 | Connected to: Not connected 50% · a signal 50% |
|
| Pin 77 | Connected to: Signal 100% |
|
| Pin 82 | Connected to: Not connected 50% · a signal 50% |
|
| Pin E10 | Connected to: Signal 100% |
|
| Pin E11 | Connected to: Signal 100% |
|
| Pin E12 | Connected to: Signal 100% |
|
| Pin E13 | Connected to: Signal 100% |
|
33 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Powerstep by rene-dev, Wifistepper by goodrobotics, PaP by brengi and Keep breathing ctrl by CV19CO.
The POWERSTEP01 in open source designs
The gallery holds 8 open source boards using the POWERSTEP01 from 6 GitHub repositories; a typical one measures about 86.4 × 65.8 mm and carries around 43 components.
75% use four copper layers or more, and 50% carry an open source license.
The most starred is Powerstep by rene-dev.
What boards using the POWERSTEP01 are built for
POWERSTEP01: common questions
Where can I find a POWERSTEP01 reference design?
Each of the 8 boards on this page is a real design using the POWERSTEP01. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the POWERSTEP01 pin 57 connected?
Pin 57 has a series capacitor on 6 of 6 designs, most often 47 nF (then 220 nF). Counted from the KiCad layouts of 6 open source designs using the POWERSTEP01.
What resistor goes on the POWERSTEP01 pin 9?
Pin 9 has a resistor to GND on 5 of 6 designs, most often 270 mΩ (then 100 mΩ). Counted from the KiCad layouts of 6 open source designs using the POWERSTEP01.
What resistor goes on the POWERSTEP01 pin 20?
Pin 20 has a resistor to GND on 5 of 6 designs, most often 270 mΩ (then 100 mΩ). Counted from the KiCad layouts of 6 open source designs using the POWERSTEP01.
Which microcontrollers do boards using the POWERSTEP01 use?
Most are built on ESP32 (1), FPGA (1) and STM32 (1).
How big is a typical board using the POWERSTEP01?
The median is 86.4 × 65.8 mm, and 25% are two-layer designs.
What is the most popular open source board using the POWERSTEP01?
By GitHub stars, Powerstep by rene-dev, with 979 stars.
Can I simulate one of these boards using the POWERSTEP01 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.