9 open source boards using the ROTARY_ENCODER

Real designs built with the ROTARY_ENCODER, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the ROTARY_ENCODER

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ROTARY_ENCODER connects to, and the resistors, capacitors and other passives placed on it.

  • The B pin has a pull-up to 3.3V on 4 of 4 designs, most often 10 kΩ (then 1 kΩ).
  • The SW1 pins have a pull-up to 3.3V on 4 of 4 designs, most often 10 kΩ.
  • The A pin has a pull-up to 3.3V on 3 of 4 designs, most often 1 kΩ (then 10 kΩ).
  • The B pin has a series resistor on 3 of 4 designs, most often 470 Ω (then 10 kΩ).
Apin 1Connected to: Signal 75% · GND 25%
  • Pull-up to 3.3V on 75% · 1 kΩ (2), 10 kΩ (1)
  • Series resistor on 50% · 470 Ω (2)
Cpin 2Connected to: GND 75% · a signal 25%
Bpin 3Connected to: Signal 100%
  • Pull-up to 3.3V on 100% · 10 kΩ (2), 1 kΩ (2)
  • Series resistor on 75% · 470 Ω (2), 10 kΩ (1)
SW1pin 4, 5Connected to: GND 50% · a signal 50%
  • Pull-up to 3.3V on 100% · 10 kΩ (4)
  • Series resistor on 75% · 10 kΩ (3)
SHpin 6Connected to: GND 100%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BGeigieIntegrated by IRNAS, OneMicro-Base-Board by ExploreEmbedded, Main V5 by cmsc-stageworks and Rotary encoder with easyC by SolderedElectronics.

The ROTARY_ENCODER in open source designs

The gallery holds 9 open source boards using the ROTARY_ENCODER from 5 GitHub repositories; a typical one measures about 66.8 × 104.8 mm and carries around 22 components.

89% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.

The most starred is BGeigieIntegrated by IRNAS.

Parts used alongside the ROTARY_ENCODER

Microcontrollers on boards using the ROTARY_ENCODER

What boards using the ROTARY_ENCODER are built for

ROTARY_ENCODER: common questions

Where can I find a ROTARY_ENCODER reference design?

Each of the 9 boards on this page is a real design using the ROTARY_ENCODER. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ROTARY_ENCODER B pin?

The B pin has a pull-up to 3.3V on 4 of 4 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 5 open source designs using the ROTARY_ENCODER.

What pull-up resistor is used on the ROTARY_ENCODER SW1 pin?

The SW1 pins have a pull-up to 3.3V on 4 of 4 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the ROTARY_ENCODER.

What pull-up resistor is used on the ROTARY_ENCODER A pin?

The A pin has a pull-up to 3.3V on 3 of 4 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the ROTARY_ENCODER.

Which microcontrollers do boards using the ROTARY_ENCODER use?

Most are built on AVR/Arduino (7).

How big is a typical board using the ROTARY_ENCODER?

The median is 66.8 × 104.8 mm, and 89% are two-layer designs.

What is the most popular open source board using the ROTARY_ENCODER?

By GitHub stars, BGeigieIntegrated by IRNAS, with 6 stars.

Can I simulate one of these boards using the ROTARY_ENCODER before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part