7 open source boards using the RTL8211F-CG
Real designs built with the RTL8211F-CG, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Mes main board
jmh8231-Dev
160 × 145 mm727 parts6LNo license2STM32
Pcb trace length analyzer
embeddedci-com
100 × 100 mm364 parts6LNo license2FPGA
MA-XILINX-FPGA-10-LAYER
moafkaljabi
84.2 × 53.6 mm425 parts10LNo license1FPGA
FPGA-Board
AbdulAjadi1
132.6 × 97.9 mm569 parts8LNo license0Artificer-A1-Single-Board-Computer
MattSpot10
115 × 90 mm486 parts6LMIT0FPGA
Zebra-X
Dylanfg123
90 × 60 mm423 parts10LNo license0- schematic only · 92 parts
ACU5EV SoM Carrier Board
raonslab2
92 parts6LNo license0
How designs wire the RTL8211F-CG
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the RTL8211F-CG connects to, and the resistors, capacitors and other passives placed on it.
- The RXD3/PHYAD0 pin has a series resistor on 6 of 6 designs, most often 22 Ω (then 4.7 kΩ).
- The REG_OUT pin has a inductor on 6 of 6 designs, most often 4.7 µH (then 3.3 µH).
- The LED1/CFG_LDO0 pin has a resistor to GND on 6 of 6 designs, most often 4.7 kΩ.
- The RSET pin has a resistor to GND on 6 of 6 designs, most often 2.49 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| AVDD10pin 3, 8, 38 | Connected to: 1V 50% · a signal 50% |
|
| AVDD33pin 11, 40 | Connected to: 3.3V 50% · a signal 50% |
|
| PHYRSTBpin 12 | Connected to: The microcontroller 67% |
|
| MDCpin 13 | Connected to: The microcontroller 83% |
|
| MDIOpin 14 | Connected to: The microcontroller 83% |
|
| TXD3pin 15 | Connected to: Signal 100% |
|
| TXD2pin 16 | Connected to: Signal 100% |
|
| TXD1pin 17 | Connected to: Signal 100% |
|
| TXD0pin 18 | Connected to: Signal 100% |
|
| TXCTLpin 19 | Connected to: Signal 100% |
|
| TXCpin 20 | Connected to: Signal 100% |
|
| DVDD10pin 21 | Connected to: 1V 50% · a signal 50% |
|
| RXD3/PHYAD0pin 22 | Connected to: Signal 100% |
|
| RXD2/PLLOFFpin 23 | Connected to: Signal 100% |
|
| RXD1/TXDLYpin 24 | Connected to: Signal 100% |
|
| RXD0/RXDLYpin 25 | Connected to: Signal 100% |
|
| RXCTL/PHYAD2pin 26 | Connected to: Signal 100% |
|
| RXC/PHYAD1pin 27 | Connected to: Signal 100% |
|
| DVDD_RGpin 28 | Connected to: 3.3V 50% · a signal 50% |
|
| DVDD33pin 29 | Connected to: 3.3V 50% · a signal 50% |
|
| REG_OUTpin 30 | Connected to: Signal 100% |
|
| INTB/PMEBpin 31 | Connected to: The microcontroller 83% |
|
| LED0/CFG_EXTpin 32 | Connected to: Signal 100% |
|
| LED1/CFG_LDO0pin 33 | Connected to: Signal 100% |
|
| LED2/CFG_LDO1pin 34 | Connected to: Signal 100% |
|
| CLKOUTpin 35 | Connected to: Signal 100% |
|
| XTAL_INpin 36 | Connected to: Signal 83% · GND 17% |
|
| XTAL_OUT/EXT_CLKpin 37 | Connected to: Signal 100% |
|
| RSETpin 39 | Connected to: Signal 100% |
|
| GNDpin 41 | Connected to: GND 100% | — |
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pcb trace length analyzer by embeddedci-com, Mes main board by jmh8231-Dev, MA-XILINX-FPGA-10-LAYER by moafkaljabi and FPGA-Board by AbdulAjadi1.
The RTL8211F-CG in open source designs
The gallery holds 7 open source boards using the RTL8211F-CG from 7 GitHub repositories; a typical one measures about 107.5 × 93.9 mm and carries around 425 components.
100% use four copper layers or more, and 14% carry an open source license.
The most starred is Mes main board by jmh8231-Dev.
Parts used alongside the RTL8211F-CG
What boards using the RTL8211F-CG are built for
RTL8211F-CG: common questions
Where can I find a RTL8211F-CG reference design?
Each of the 7 boards on this page is a real design using the RTL8211F-CG. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the RTL8211F-CG RXD3/PHYAD0 pin?
The RXD3/PHYAD0 pin has a series resistor on 6 of 6 designs, most often 22 Ω (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the RTL8211F-CG.
How is the RTL8211F-CG REG_OUT pin connected?
The REG_OUT pin has a inductor on 6 of 6 designs, most often 4.7 µH (then 3.3 µH). Counted from the KiCad layouts of 6 open source designs using the RTL8211F-CG.
What resistor goes on the RTL8211F-CG LED1/CFG_LDO0 pin?
The LED1/CFG_LDO0 pin has a resistor to GND on 6 of 6 designs, most often 4.7 kΩ. Counted from the KiCad layouts of 6 open source designs using the RTL8211F-CG.
What parts are used alongside the RTL8211F-CG?
The 93LC56B-I/SN, LS1205EVD33, STM32MP257FAI3, SY8003ADFC and USB3320C-EZK appear in the most repositories here.
Which microcontrollers do boards using the RTL8211F-CG use?
Most are built on FPGA (3) and STM32 (2).
How big is a typical board using the RTL8211F-CG?
The median is 107.5 × 93.9 mm, and 0% are two-layer designs.
What is the most popular open source board using the RTL8211F-CG?
By GitHub stars, Mes main board by jmh8231-Dev, with 2 stars.
Can I simulate one of these boards using the RTL8211F-CG before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.