11 open source boards using the USB3320C-EZK
Real designs built with the USB3320C-EZK, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
HFLink
LX050724
48.5 × 33.5 mm111 parts4LApache-2.024FPGA
IO-SDR
rishivg
99.4 × 60 mm309 parts8LCERN-OHL-S-2.010STM32
R2RDAC2026 REVIZE II
ERDALECE
246 × 120 mm919 parts6LGPL-3.05STM32
Dev Board STM32F769
MarvinBrth
52 × 52 mm138 parts6LNo license1PSEC5 Ctrl Board
AhanDatta
197 × 130 mm518 parts10LNo license0FPGA
Zebra-X
Dylanfg123
90 × 60 mm423 parts10LNo license0SimpleCarrier
alexian79
105.6 × 100.9 mm109 parts6LBSD-2-Clause0STM32
Prism mainboard
AveragePillow17
100 × 100 mm82 parts6LNo license0- schematic only · 92 parts
ACU5EV SoM Carrier Board
raonslab2
92 parts6LNo license0 STM32
Device
jayis1
85 × 54 mm21 parts4LNo license3EAG-7000 — Edge AI Gateway
jayis1
100 × 72 mm10 parts10LNo license0
How designs wire the USB3320C-EZK
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the USB3320C-EZK connects to, and the resistors, capacitors and other passives placed on it.
- The RBIAS pin has a resistor to GND on 6 of 8 designs, most often 8.06 kΩ.
- The SPK_L pin is left unconnected on 7 of 8 designs.
- The SPK_R pin is left unconnected on 7 of 8 designs.
- The VDD33 pin has a decoupling capacitor on 5 of 8 designs, most often 100 nF (then 2.2 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 12 | Connected to: Not connected 88% | — |
| SPK_Lpin 15 | Connected to: Not connected 88% | — |
| SPK_Rpin 16 | Connected to: Not connected 88% | — |
| VDD33pin 20 | Connected to: 3.3V 50% · a signal 25% |
|
| VBATpin 21 | Connected to: 3.3V 88% |
|
| VBUSpin 22 | Connected to: Signal 75% · 5V 25% |
|
| IDpin 23 | Connected to: A connector 25% · not connected 25% |
|
| RBIASpin 24 | Connected to: Signal 75% · not connected 25% |
|
| XOpin 25 | Connected to: Not connected 75% · a signal 25% | — |
| REFCLKpin 26 | Connected to: Signal 75% · not connected 25% |
|
| RESETBpin 27 | Connected to: A connector 38%, the microcontroller 38% · not connected 25% |
|
| VDD18pin 28, 30 | Connected to: 1.8V 71% |
|
| VDDIOpin 32 | Connected to: 1.8V 86% |
|
| GNDpin 33 | Connected to: GND 71% · not connected 29% | — |
18 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include HFLink by LX050724, IO-SDR by rishivg, R2RDAC2026 REVIZE II by ERDALECE and Dev Board STM32F769 by MarvinBrth.
The USB3320C-EZK in open source designs
The gallery holds 11 open source boards using the USB3320C-EZK from 11 GitHub repositories; a typical one measures about 99.7 × 66 mm and carries around 111 components.
100% use four copper layers or more, and 36% carry an open source license.
The most starred is HFLink by LX050724.
Parts used alongside the USB3320C-EZK
What boards using the USB3320C-EZK are built for
USB3320C-EZK: common questions
Where can I find a USB3320C-EZK reference design?
Each of the 11 boards on this page is a real design using the USB3320C-EZK. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the USB3320C-EZK RBIAS pin?
The RBIAS pin has a resistor to GND on 6 of 8 designs, most often 8.06 kΩ. Counted from the KiCad layouts of 8 open source designs using the USB3320C-EZK.
How is the USB3320C-EZK SPK_L pin connected?
The SPK_L pin is left unconnected on 7 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the USB3320C-EZK.
How is the USB3320C-EZK SPK_R pin connected?
The SPK_R pin is left unconnected on 7 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the USB3320C-EZK.
Which microcontrollers do boards using the USB3320C-EZK use?
Most are built on STM32 (4) and FPGA (2).
How big is a typical board using the USB3320C-EZK?
The median is 99.7 × 66 mm, and 0% are two-layer designs.
What is the most popular open source board using the USB3320C-EZK?
By GitHub stars, HFLink by LX050724, with 24 stars.
Can I simulate one of these boards using the USB3320C-EZK before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.