8 open source boards using the RX5808
Real designs built with the RX5808, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
FPV Receiver Diversity Pro Part1/2
Virtex7
50 × 29.5 mm53 parts2LNo license8ESP32
Deets fpv vtx scanner
deets
65.8 × 77.2 mm31 parts4LNo license5STM32
Rx5808-receiver
msaribekyan
50 × 25 mm38 parts2LGPL-3.03ESP32
Fpvlaptracker
warhog
49 × 49.9 mm28 parts2LMIT3AVR/Arduino
Rx5808-video receiver
nykleban
80.7 × 102.7 mm81 parts4LNo license0AVR/Arduino
Race-Timer
MissouriMRR
150 × 150 mm27 parts2LNo license0Diversity-Modul für den RX5823
Virtex7
56.5 × 25 mm43 parts2LNo license8Raspberry Pi
Ground station
ShaneTWilliams
65 × 59.5 mm117 parts4LNo license3
How designs wire the RX5808
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the RX5808 connects to, and the resistors, capacitors and other passives placed on it.
- The CH1 pin has a series resistor on 3 of 7 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CH1pin 9 | Connected to: A connector 29% |
|
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Diversity-Modul für den RX5823 by Virtex7, Deets fpv vtx scanner by deets, Rx5808-receiver by msaribekyan and Ground station by ShaneTWilliams.
The RX5808 in open source designs
The gallery holds 8 open source boards using the RX5808 from 7 GitHub repositories; a typical one measures about 60.8 × 54.7 mm and carries around 41 components.
63% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is FPV Receiver Diversity Pro Part1/2 by Virtex7.
Microcontrollers on boards using the RX5808
What boards using the RX5808 are built for
RX5808: common questions
Where can I find a RX5808 reference design?
Each of the 8 boards on this page is a real design using the RX5808. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the RX5808 CH1 pin?
The CH1 pin has a series resistor on 3 of 7 designs, most often 10 kΩ. Counted from the KiCad layouts of 7 open source designs using the RX5808.
Which microcontrollers do boards using the RX5808 use?
Most are built on AVR/Arduino (3), ESP32 (2), Raspberry Pi (1) and STM32 (1).
How big is a typical board using the RX5808?
The median is 60.8 × 54.7 mm, and 63% are two-layer designs.
What is the most popular open source board using the RX5808?
By GitHub stars, FPV Receiver Diversity Pro Part1/2 by Virtex7, with 8 stars.
Can I simulate one of these boards using the RX5808 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.