8 open source boards using the SN74LVC2G17DCKR
Real designs built with the SN74LVC2G17DCKR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Remram
hasenbanck
140 × 104 mm259 parts4LNo license40ESP32
Main routed
0x63616c
54 × 71 mm194 parts4LNo license0RP2040/RP2350
4in gps
sonicavionics
84.1 × 61.7 mm84 parts4LMIT0TMSRGBCustom Hat v1 for JFF
herraa1
56 × 58 mm46 parts2LGPL-3.02ESP32
Main test
0x63616c
54 × 71 mm194 parts4LNo license0AVR/Arduino
Numpad
SirBramble
126 × 126 mm84 parts2LMIT0ESP32
Controller test
0x63616c
61 parts2LNo license0ESP32
ARDF-TX UNIVERSAL CONTROLLER
DD1SB
100 × 100 mm197 parts2LMIT0
How designs wire the SN74LVC2G17DCKR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the SN74LVC2G17DCKR connects to, and the resistors, capacitors and other passives placed on it.
- The 1A pin has a series resistor on 4 of 6 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The 2A pin has a series resistor on 3 of 6 designs, most often 4.7 kΩ (then 10 kΩ).
- The VCC pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1Apin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 67% · a signal 33% | — |
| 2Apin 3 | Connected to: Signal 83% · GND 17% |
|
| 2Ypin 4 | Connected to: The microcontroller 33%, a connector 33% |
|
| VCCpin 5 | Connected to: 5V 67% · a signal 33% |
|
| 1Ypin 6 | Connected to: The microcontroller 50% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Remram by hasenbanck, TMSRGBCustom Hat v1 for JFF by herraa1, Controller test by 0x63616c and ARDF-TX UNIVERSAL CONTROLLER by DD1SB.
The SN74LVC2G17DCKR in open source designs
The gallery holds 8 open source boards using the SN74LVC2G17DCKR from 6 GitHub repositories; a typical one measures about 84.1 × 71 mm and carries around 139 components.
50% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Remram by hasenbanck.
Microcontrollers on boards using the SN74LVC2G17DCKR
What boards using the SN74LVC2G17DCKR are built for
SN74LVC2G17DCKR: common questions
Where can I find a SN74LVC2G17DCKR reference design?
Each of the 8 boards on this page is a real design using the SN74LVC2G17DCKR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the SN74LVC2G17DCKR 1A pin?
The 1A pin has a series resistor on 4 of 6 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 6 open source designs using the SN74LVC2G17DCKR.
What resistor goes on the SN74LVC2G17DCKR 2A pin?
The 2A pin has a series resistor on 3 of 6 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the SN74LVC2G17DCKR.
What decoupling capacitors do designs use on the SN74LVC2G17DCKR VCC pin?
The VCC pin has a decoupling capacitor on 3 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the SN74LVC2G17DCKR.
Which microcontrollers do boards using the SN74LVC2G17DCKR use?
Most are built on ESP32 (4), AVR/Arduino (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the SN74LVC2G17DCKR?
The median is 84.1 × 71 mm, and 50% are two-layer designs.
What is the most popular open source board using the SN74LVC2G17DCKR?
By GitHub stars, Remram by hasenbanck, with 40 stars.
Can I simulate one of these boards using the SN74LVC2G17DCKR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.