6 open source boards using the SP3485
Real designs built with the SP3485, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Taiko-256
AnalogDragon
170 × 120 mm261 parts2LCustom license7Control
Jochen0x90h
70 × 76 mm78 parts2LCC-BY-NC-4.03AVR/Arduino
Radio module
tmolteno
69.7 × 37.4 mm110 parts6LGPL-3.01ESP32
Bldc sic
klaus-liebler
60 × 63 mm113 parts2LMIT0Ews tbeam mainboard
venougm
205 × 124 mm49 parts2LNo license0ESP32
Bldc
klaus-liebler
58 × 60 mm112 parts2LMIT0
How designs wire the SP3485
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the SP3485 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 22 µF).
- The B pin has a series resistor on 4 of 5 designs, most often 120 Ω.
- The A pin has a series resistor on 3 of 5 designs, most often 120 Ω.
- The RO pin has a series resistor on 2 of 5 designs, most often 33 kΩ (then 1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ROpin 1 | Connected to: A connector 60%, the microcontroller 60% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| Apin 6 | Connected to: A connector 60% |
|
| Bpin 7 | Connected to: A connector 60% |
|
| VCCpin 8 | Connected to: 3.3V 100% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Taiko-256 by AnalogDragon, Control by Jochen0x90h, Radio module by tmolteno and Bldc by klaus-liebler.
The SP3485 in open source designs
The gallery holds 6 open source boards using the SP3485 from 5 GitHub repositories; a typical one measures about 69.8 × 69.5 mm and carries around 111 components.
83% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Taiko-256 by AnalogDragon.
Parts used alongside the SP3485
Microcontrollers on boards using the SP3485
What boards using the SP3485 are built for
SP3485: common questions
Where can I find a SP3485 reference design?
Each of the 6 boards on this page is a real design using the SP3485. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SP3485 VCC pin?
The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 5 open source designs using the SP3485.
What resistor goes on the SP3485 B pin?
The B pin has a series resistor on 4 of 5 designs, most often 120 Ω. Counted from the KiCad layouts of 5 open source designs using the SP3485.
What resistor goes on the SP3485 A pin?
The A pin has a series resistor on 3 of 5 designs, most often 120 Ω. Counted from the KiCad layouts of 5 open source designs using the SP3485.
Which microcontrollers do boards using the SP3485 use?
Most are built on ESP32 (2), AVR/Arduino (1) and STM32 (1).
How big is a typical board using the SP3485?
The median is 69.8 × 69.5 mm, and 83% are two-layer designs.
What is the most popular open source board using the SP3485?
By GitHub stars, Taiko-256 by AnalogDragon, with 7 stars.
Can I simulate one of these boards using the SP3485 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.