6 open source boards using the SPL06-001
Real designs built with the SPL06-001, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
AutoPilotPi-Hardware
AutopilotPi
29 × 52 mm97 parts4LGPL-3.035ESP32
Blinkekatze
TobleMiner
83 × 83 mm106 parts4LNo license34STM32
Zero star
Auodit
38 × 38 mm127 parts4LCC-BY-SA-4.00ESP32
STRATOSDRONES
equationstratos
38 × 74 mm109 parts4LMIT0STM32
Zero star rounded
Auodit
38 × 38 mm110 parts4LCC-BY-SA-4.00Hardware
vili111111p
39 × 39 mm104 parts4LNo license0
How designs wire the SPL06-001
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the SPL06-001 connects to, and the resistors, capacitors and other passives placed on it.
- The VDDIO pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 1 µF).
- The VDD pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 1 µF).
- The SDA pin has a pull-up to 3.3V on 3 of 5 designs, most often 4.7 kΩ.
- The SCK pin has a pull-up to 3.3V on 3 of 5 designs, most often 4.7 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 7 | Connected to: GND 100% | — |
| SDApin 3 | Connected to: The microcontroller 80% |
|
| SCKpin 4 | Connected to: The microcontroller 80% |
|
| VDDIOpin 6 | Connected to: 3.3V 80% · a signal 20% |
|
| VDDpin 8 | Connected to: 3.3V 80% · a signal 20% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AutoPilotPi-Hardware by AutopilotPi, Blinkekatze by TobleMiner, Zero star by Auodit and STRATOSDRONES by equationstratos.
The SPL06-001 in open source designs
The gallery holds 6 open source boards using the SPL06-001 from 5 GitHub repositories; a typical one measures about 38 × 45.5 mm and carries around 108 components.
100% use four copper layers or more, and 67% carry an open source license.
The most starred is AutoPilotPi-Hardware by AutopilotPi.
Parts used alongside the SPL06-001
What boards using the SPL06-001 are built for
SPL06-001: common questions
Where can I find a SPL06-001 reference design?
Each of the 6 boards on this page is a real design using the SPL06-001. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SPL06-001 VDDIO pin?
The VDDIO pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the SPL06-001.
What decoupling capacitors do designs use on the SPL06-001 VDD pin?
The VDD pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the SPL06-001.
What pull-up resistor is used on the SPL06-001 SDA pin?
The SDA pin has a pull-up to 3.3V on 3 of 5 designs, most often 4.7 kΩ. Counted from the KiCad layouts of 5 open source designs using the SPL06-001.
Which microcontrollers do boards using the SPL06-001 use?
Most are built on ESP32 (2), STM32 (2) and FPGA (1).
How big is a typical board using the SPL06-001?
The median is 38 × 45.5 mm, and 0% are two-layer designs.
What is the most popular open source board using the SPL06-001?
By GitHub stars, AutoPilotPi-Hardware by AutopilotPi, with 35 stars.
Can I simulate one of these boards using the SPL06-001 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.