8 open source boards using the ST1S14PHR

Real designs built with the ST1S14PHR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the ST1S14PHR

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ST1S14PHR connects to, and the resistors, capacitors and other passives placed on it.

  • The BOOT_1 pin has a series capacitor on 7 of 7 designs, most often 100 nF.
  • The VIN_7 pin has a decoupling capacitor on 7 of 7 designs, most often 10 µF (then 100 nF).
  • The SW_8 pin has a inductor on 7 of 7 designs, most often 10 µH (then 22 µH).
  • The SW_8 pin has a series capacitor on 6 of 7 designs, most often 100 nF.
BOOT_1pin 1Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (7)
EN1pin 3Connected to: GND 71% · a signal 29%
FB_4pin 4Connected to: Signal 100%
  • Resistor to GND on 71% · 10 kΩ (2), 48.7 kΩ (1), 1.1 kΩ (1)
  • Series resistor on 71% · 6.2 kΩ (2), 82.5 kΩ (1), 220 Ω (1)
  • Pull-up to 5V on 43% · 9.53 kΩ (1), 10 kΩ (1), 8.45 kΩ (1)
EN2_5pin 5Connected to: Signal 57% · 33V 43%
  • Resistor to GND on 43% · 47 kΩ (2), 100 kΩ (1)
  • Capacitor to GND on 43% · 10 µF (4), 100 nF (2), 6.8 mF (1)
GND_6pin 6Connected to: GND 100%
VIN_7pin 7Connected to: 24V 86%
  • Decoupling capacitor on 100% · 10 µF (6), 100 nF (5), 68 nF (1)
SW_8pin 8Connected to: Signal 100%
  • Inductor on 100% · 10 µH (2), 22 µH (2), 6.8 µH (1)
  • Series capacitor on 86% · 100 nF (6)
EP_9pin 9Connected to: GND 100%

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include KiCad by Kampi, Amp board by Alex-Wolfe, BMS by buglalis and PDB by CalebJM04.

The ST1S14PHR in open source designs

The gallery holds 8 open source boards using the ST1S14PHR from 7 GitHub repositories; a typical one measures about 101.5 × 98.1 mm and carries around 162 components.

88% use four copper layers or more, and 13% carry an open source license.

The most starred is KiCad by Kampi.

Microcontrollers on boards using the ST1S14PHR

What boards using the ST1S14PHR are built for

ST1S14PHR: common questions

Where can I find a ST1S14PHR reference design?

Each of the 8 boards on this page is a real design using the ST1S14PHR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ST1S14PHR BOOT_1 pin connected?

The BOOT_1 pin has a series capacitor on 7 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the ST1S14PHR.

What decoupling capacitors do designs use on the ST1S14PHR VIN_7 pin?

The VIN_7 pin has a decoupling capacitor on 7 of 7 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the ST1S14PHR.

How is the ST1S14PHR SW_8 pin connected?

The SW_8 pin has a inductor on 7 of 7 designs, most often 10 µH (then 22 µH). Counted from the KiCad layouts of 7 open source designs using the ST1S14PHR.

What parts are used alongside the ST1S14PHR?

The ESP32-WROOM-32E-N4, INA238AIDGSR, LM3429MH/NOPB, MCP7940N-I/SN and ST1S10PHR appear in the most repositories here.

Which microcontrollers do boards using the ST1S14PHR use?

Most are built on ESP32 (2), STM32 (2) and PIC (1).

How big is a typical board using the ST1S14PHR?

The median is 101.5 × 98.1 mm, and 13% are two-layer designs.

What is the most popular open source board using the ST1S14PHR?

By GitHub stars, KiCad by Kampi, with 3 stars.

Can I simulate one of these boards using the ST1S14PHR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part