6 open source boards using the MCP7940N-I/SN

Real designs built with the MCP7940N-I/SN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the MCP7940N-I/SN

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MCP7940N-I/SN connects to, and the resistors, capacitors and other passives placed on it.

  • The X1 pin has a crystal on 5 of 5 designs, most often 32.768 kHz.
  • The X1 pin has a capacitor to GND on 5 of 5 designs, most often 10 pF (then 7 pF).
  • The X2 pin has a crystal on 5 of 5 designs, most often 32.768 kHz.
  • The X2 pin has a capacitor to GND on 5 of 5 designs, most often 10 pF (then 7 pF).
X1pin 1Connected to: Signal 100%
  • Crystal on 100% · 32.768 kHz (3)
  • Capacitor to GND on 100% · 10 pF (2), 7 pF (1), 18 pF (1)
X2pin 2Connected to: Signal 100%
  • Crystal on 100% · 32.768 kHz (3)
  • Capacitor to GND on 100% · 10 pF (2), 7 pF (1), 18 pF (1)
VBATpin 3Connected to: VBAT 60% · not connected 20% · a signal 20%
VSSpin 4Connected to: GND 100%
SDApin 5Connected to: The microcontroller 40%
  • Series resistor on 80% · 100 Ω (3), 4.7 kΩ (1)
  • Pull-up to 3.3V on 80% · 4.7 kΩ (3), 10 kΩ (1)
SCLpin 6Connected to: The microcontroller 40%
  • Series resistor on 80% · 100 Ω (3), 4.7 kΩ (1)
  • Pull-up to 3.3V on 80% · 4.7 kΩ (3), 10 kΩ (1)
MFPpin 7Connected to: Not connected 80% · a signal 20%
VCCpin 8Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 100% · 100 nF (5), 22 µF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AnthC by Anthilla, X16-fpga board by eshankiyer, EU-LITE / routed draft by nikolajevs and PCB EU by nikolajevs.

The MCP7940N-I/SN in open source designs

The gallery holds 6 open source boards using the MCP7940N-I/SN from 5 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 173 components.

83% use four copper layers or more, and 0% carry an open source license.

The most starred is AnthC by Anthilla.

Microcontrollers on boards using the MCP7940N-I/SN

MCP7940N-I/SN: common questions

Where can I find a MCP7940N-I/SN reference design?

Each of the 6 boards on this page is a real design using the MCP7940N-I/SN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MCP7940N-I/SN X1 pin connected?

The X1 pin has a crystal on 5 of 5 designs, most often 32.768 kHz. Counted from the KiCad layouts of 5 open source designs using the MCP7940N-I/SN.

How is the MCP7940N-I/SN X2 pin connected?

The X2 pin has a crystal on 5 of 5 designs, most often 32.768 kHz. Counted from the KiCad layouts of 5 open source designs using the MCP7940N-I/SN.

What decoupling capacitors do designs use on the MCP7940N-I/SN VCC pin?

The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 5 open source designs using the MCP7940N-I/SN.

What parts are used alongside the MCP7940N-I/SN?

The ESP32-WROOM-32E-N4, INA238AIDGSR, LM3429MH/NOPB, ST1S10PHR and ST1S14PHR appear in the most repositories here.

Which microcontrollers do boards using the MCP7940N-I/SN use?

Most are built on ESP32 (4) and FPGA (1).

How big is a typical board using the MCP7940N-I/SN?

The median is 100 × 100 mm, and 17% are two-layer designs.

What is the most popular open source board using the MCP7940N-I/SN?

By GitHub stars, AnthC by Anthilla, with 40 stars.

Can I simulate one of these boards using the MCP7940N-I/SN before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part