6 open source boards using the ST1S10PHR
Real designs built with the ST1S10PHR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Hermes-Lite 2.0
softerhardware
100 × 100 mm488 parts4LNo license372FPGA
Spla
khaydarian
165 × 107 mm252 parts4LNo license32STM32
Stm32mp1-custom devboard
voloviq
120 × 80.6 mm194 parts4LNo license7ESP32
EU-LITE / routed draft
nikolajevs
100 × 100 mm158 parts4LNo license0FPGA
HL2 Filter Board
softerhardware
100 × 49.9 mm112 parts4LNo license372ESP32
EU-LITE / routed draft
nikolajevs
100 × 100 mm158 parts4LNo license0
How designs wire the ST1S10PHR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ST1S10PHR connects to, and the resistors, capacitors and other passives placed on it.
- The VFB pin has a resistor to GND on 5 of 5 designs, most often 100 kΩ (then 47 kΩ).
- The VIN_SW pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 100 nF).
- The SW pin has a inductor on 5 of 5 designs, most often 3.3 µH (then 2.2 µH).
- The VIN_A pin has a decoupling capacitor on 4 of 5 designs, most often 10 µF (then 4.7 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VIN_Apin 1 | Connected to: 12V 60% · a signal 40% |
|
| INHpin 2 | Connected to: 12V 60% · a signal 40% | — |
| VFBpin 3 | Connected to: Signal 100% |
|
| AGNDpin 4 | Connected to: GND 100% | — |
| SYNCpin 5 | Connected to: GND 80% · a signal 20% | — |
| VIN_SWpin 6 | Connected to: 12V 60% · a signal 40% |
|
| SWpin 7 | Connected to: Signal 100% |
|
| PGNDpin 8 | Connected to: GND 100% | — |
| Pin 9 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hermes-Lite 2.0 by softerhardware, Spla by khaydarian, Stm32mp1-custom devboard by voloviq and EU-LITE / routed draft by nikolajevs.
The ST1S10PHR in open source designs
The gallery holds 6 open source boards using the ST1S10PHR from 5 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 176 components.
100% use four copper layers or more, and 0% carry an open source license.
The most starred is Hermes-Lite 2.0 by softerhardware.
Parts used alongside the ST1S10PHR
What boards using the ST1S10PHR are built for
ST1S10PHR: common questions
Where can I find a ST1S10PHR reference design?
Each of the 6 boards on this page is a real design using the ST1S10PHR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the ST1S10PHR VFB pin?
The VFB pin has a resistor to GND on 5 of 5 designs, most often 100 kΩ (then 47 kΩ). Counted from the KiCad layouts of 5 open source designs using the ST1S10PHR.
What decoupling capacitors do designs use on the ST1S10PHR VIN_SW pin?
The VIN_SW pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the ST1S10PHR.
How is the ST1S10PHR SW pin connected?
The SW pin has a inductor on 5 of 5 designs, most often 3.3 µH (then 2.2 µH). Counted from the KiCad layouts of 5 open source designs using the ST1S10PHR.
What parts are used alongside the ST1S10PHR?
The USBLC6-2SC6, ESP32-WROOM-32E-N4, INA238AIDGSR, LM3429MH/NOPB and MCP7940N-I/SN appear in the most repositories here.
Which microcontrollers do boards using the ST1S10PHR use?
Most are built on FPGA (3), ESP32 (2) and STM32 (1).
How big is a typical board using the ST1S10PHR?
The median is 100 × 100 mm, and 0% are two-layer designs.
What is the most popular open source board using the ST1S10PHR?
By GitHub stars, Hermes-Lite 2.0 by softerhardware, with 372 stars.
Can I simulate one of these boards using the ST1S10PHR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.