15 open source boards using the TCAN3413DR
Real designs built with the TCAN3413DR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
SylionX
AmalRajKC
72 × 22 mm41 parts2LCERN-OHL-S-2.04STM32
Esc rev b
iamdarshg
173.8 × 282.9 mm687 parts4LNo license2Canfdshield
feaser
53.9 × 53.3 mm14 parts4LMIT1RP2040/RP2350
ThumbMuncher
Alsa2
52 × 51 mm82 parts4LNo license0STM32
Esc rev b.before hand power replicate
iamdarshg
170 × 172.2 mm681 parts6LNo license2STM32
Backplane Prototype
kquinsland
151.8 × 30.8 mm70 parts4LNo license0STM32
Mini Rack Power Carrier
kquinsland
100 × 34.9 mm61 parts4LNo license0Main rev b final
iamdarshg
130 × 74.5 mm167 parts4LNo license2Main rev b final.before diff pair ripup
iamdarshg
130 × 74.5 mm167 parts4LNo license2Main rev b
iamdarshg
140 × 100 mm161 parts4LNo license2Main rev b completed
iamdarshg
140 × 100 mm161 parts4LNo license2Main rev b routed
iamdarshg
140 × 100 mm161 parts4LNo license2Main rev b routed clean
iamdarshg
140 × 100 mm161 parts4LNo license2Main rev b routed iter2 filled
iamdarshg
140 × 100 mm161 parts4LNo license2Main rev b shortfix
iamdarshg
140 × 100 mm161 parts4LNo license2
How designs wire the TCAN3413DR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TCAN3413DR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 4.7 µF).
- The CANL pin has a series resistor on 4 of 5 designs, most often 120 Ω.
- The STB pin is tied to GND on 3 of 5 designs (a signal on 2).
- The VIO pin has a decoupling capacitor on 2 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VCCpin 3 | Connected to: 3.3V 100% |
|
| VIOpin 5 | Connected to: 3.3V 100% |
|
| CANLpin 6 | Connected to: A connector 60% |
|
| CANHpin 7 | Connected to: A connector 60% |
|
| STBpin 8 | Connected to: GND 60% · a signal 40% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include SylionX by AmalRajKC, Esc rev b by iamdarshg, Canfdshield by feaser and ThumbMuncher by Alsa2.
The TCAN3413DR in open source designs
The gallery holds 15 open source boards using the TCAN3413DR from 5 GitHub repositories; a typical one measures about 140 × 100 mm and carries around 161 components.
93% use four copper layers or more, and 13% carry an open source license.
The most starred is SylionX by AmalRajKC.
Parts used alongside the TCAN3413DR
Microcontrollers on boards using the TCAN3413DR
What boards using the TCAN3413DR are built for
TCAN3413DR: common questions
Where can I find a TCAN3413DR reference design?
Each of the 15 boards on this page is a real design using the TCAN3413DR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TCAN3413DR VCC pin?
The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 5 open source designs using the TCAN3413DR.
What resistor goes on the TCAN3413DR CANL pin?
The CANL pin has a series resistor on 4 of 5 designs, most often 120 Ω. Counted from the KiCad layouts of 5 open source designs using the TCAN3413DR.
How is the TCAN3413DR STB pin connected?
The STB pin is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the TCAN3413DR.
Which microcontrollers do boards using the TCAN3413DR use?
Most are built on STM32 (4) and RP2040/RP2350 (1).
How big is a typical board using the TCAN3413DR?
The median is 140 × 100 mm, and 7% are two-layer designs.
What is the most popular open source board using the TCAN3413DR?
By GitHub stars, SylionX by AmalRajKC, with 4 stars.
Can I simulate one of these boards using the TCAN3413DR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.