10 open source boards using the TLP175A
Real designs built with the TLP175A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Candash
miekush
100 × 80 mm90 parts2LCustom license7STM32
A1 - Analogue Board
DumberThanUsual
309.1 × 225.1 mm273 parts2LNo license1Hantek-6022
AntoninPvr
16.8 × 15 mm15 parts2LGPL-3.01Current100A Artiq
KLFAMO
161 × 100 mm324 parts4LNo license0STM32
RSC-LV3-LVBPS
cyfinfaza
210 × 60 mm118 parts2LNo license0LPV01 SHIELD
pureHK
140 × 125 mm105 parts4LNo license0STM32
USB2CAN Hardware
Mieho1
46.1 × 20.3 mm56 parts4LNo license0ESP32
ESP32 Shield Zero
ThomasLindenberger37
69 × 40.6 mm42 parts4LMIT0STM32
DSMU A1
DumberThanUsual
172.8 × 214.7 mm272 parts2LNo license1Containment simple
UWCubeSat
45.7 × 45.7 mm57 parts2LMIT1
How designs wire the TLP175A
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the TLP175A connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 8 of 9 designs, most often 470 Ω (then 1 kΩ).
- Pin 3 is tied to GND on 7 of 9 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 3 | Connected to: GND 78% · a signal 22% | — |
| Pin 4 | Connected to: A connector 67% |
|
| Pin 6 | Connected to: A connector 63% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Candash by miekush, Hantek-6022-pcb by AntoninPvr, A1 - Analogue Board by DumberThanUsual and Containment simple by UWCubeSat.
The TLP175A in open source designs
The gallery holds 10 open source boards using the TLP175A from 9 GitHub repositories; a typical one measures about 120 × 70 mm and carries around 98 components.
60% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.
The most starred is Candash by miekush.
What boards using the TLP175A are built for
TLP175A: common questions
Where can I find a TLP175A reference design?
Each of the 10 boards on this page is a real design using the TLP175A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TLP175A pin 1?
Pin 1 has a series resistor on 8 of 9 designs, most often 470 Ω (then 1 kΩ). Counted from the KiCad layouts of 9 open source designs using the TLP175A.
How is the TLP175A pin 3 connected?
Pin 3 is tied to GND on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the TLP175A.
Which microcontrollers do boards using the TLP175A use?
Most are built on STM32 (5) and ESP32 (1).
How big is a typical board using the TLP175A?
The median is 120 × 70 mm, and 60% are two-layer designs.
What is the most popular open source board using the TLP175A?
By GitHub stars, Candash by miekush, with 7 stars.
Can I simulate one of these boards using the TLP175A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.