11 open source boards using the TLV61046ADBVR
Real designs built with the TLV61046ADBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Gb fpga
blazer82
80.1 × 78.6 mm132 parts4LTAPR-OHL-1.012DMM KiCAD V4 next
oihdesigns
68.5 × 53.3 mm79 parts4LNo license2RP2040/RP2350
Aster2350
Amronos
80 × 65 mm121 parts4LApache-2.01STM32
Ir remote
danngreen
127 × 53.5 mm99 parts2LNo license0ESP32
SensoCore
Dormage
57.5 × 72 mm71 parts2LNo license0ESP32
PCB-for-IoT-enabled-Indoor-Air-Purification-System
gokul-rm
63 × 72 mm24 parts2LNo license04116
tops4u
31.8 × 37.1 mm32 parts2LGPL-3.0117FPGA
Hi board
blazer82
81 × 117 mm55 parts4LTAPR-OHL-1.012DMM Giga Shield Version
oihdesigns
95.6 × 53.3 mm77 parts4LNo license2DMM XIAO Specific Footprint
oihdesigns
68.5 × 53.3 mm76 parts4LNo license2AVR/Arduino
NametagVoltmeter
oihdesigns
88.9 × 50.8 mm66 parts4LNo license2
How designs wire the TLV61046ADBVR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TLV61046ADBVR connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 7 of 7 designs, most often 10 µH (then 4.7 µH).
- The FB pin has a resistor to GND on 6 of 7 designs, most often 180 kΩ (then 71.5 kΩ).
- The VIN pin has a inductor on 6 of 7 designs, most often 10 µH (then 4.7 µH).
- The FB pin has a pull-up to 5V on 5 of 7 designs, most often 953 kΩ (then 732 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| FBpin 3 | Connected to: Signal 86% |
|
| ENpin 4 | Connected to: Signal 71% · 5V 29% |
|
| VOUTpin 5 | Connected to: 5V 71% · a signal 29% |
|
| VINpin 6 | Connected to: 5V 71% · a signal 29% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 4116 by tops4u, Gb fpga by blazer82, DMM Giga Shield Version by oihdesigns and Aster2350 by Amronos.
The TLV61046ADBVR in open source designs
The gallery holds 11 open source boards using the TLV61046ADBVR from 7 GitHub repositories; a typical one measures about 80 × 53.5 mm and carries around 76 components.
64% use four copper layers or more, and 36% carry an open source license.
The most starred is 4116 by tops4u.
Parts used alongside the TLV61046ADBVR
Microcontrollers on boards using the TLV61046ADBVR
What boards using the TLV61046ADBVR are built for
TLV61046ADBVR: common questions
Where can I find a TLV61046ADBVR reference design?
Each of the 11 boards on this page is a real design using the TLV61046ADBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TLV61046ADBVR SW pin connected?
The SW pin has a inductor on 7 of 7 designs, most often 10 µH (then 4.7 µH). Counted from the KiCad layouts of 7 open source designs using the TLV61046ADBVR.
What resistor goes on the TLV61046ADBVR FB pin?
The FB pin has a resistor to GND on 6 of 7 designs, most often 180 kΩ (then 71.5 kΩ). Counted from the KiCad layouts of 7 open source designs using the TLV61046ADBVR.
How is the TLV61046ADBVR VIN pin connected?
The VIN pin has a inductor on 6 of 7 designs, most often 10 µH (then 4.7 µH). Counted from the KiCad layouts of 7 open source designs using the TLV61046ADBVR.
Which microcontrollers do boards using the TLV61046ADBVR use?
Most are built on ESP32 (2), FPGA (2), AVR/Arduino (1) and RP2040/RP2350 (1).
How big is a typical board using the TLV61046ADBVR?
The median is 80 × 53.5 mm, and 36% are two-layer designs.
What is the most popular open source board using the TLV61046ADBVR?
By GitHub stars, 4116 by tops4u, with 117 stars.
Can I simulate one of these boards using the TLV61046ADBVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.