8 open source boards using the TLV62568DBV
Real designs built with the TLV62568DBV, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Basic ecp5
mattvenn
100 × 68 mm62 parts4LCC0-1.0143RP2040/RP2350
MioLink
Misaka0x2730
53 × 42 mm92 parts4LGPL-3.027ESP32
NX-ISD
Ghost3379
77 × 48.6 mm108 parts4LGPL-3.02AVR/Arduino
IV6Clock2 base
SarahAlroe
99.1 × 45.7 mm36 parts2LNo license1Reform2-motherboard30
owebeeone
276 × 93.5 mm513 parts6LNo license0STM32
LogicPad
erhancm
69.1 × 104.8 mm113 parts2LApache-2.00Reform2-motherboard
owebeeone
276 × 93.5 mm501 parts6LNo license0Reform2-motherboard25
owebeeone
276 × 93.5 mm494 parts6LNo license0
How designs wire the TLV62568DBV
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TLV62568DBV connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 6 of 6 designs, most often 2.2 µH (then 1 µH).
- The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 4.7 µF (then 10 µF).
- The FB pin has a resistor to GND on 6 of 6 designs, most often 100 kΩ (then 120 kΩ).
- The FB pin has a pull-up to 3.3V on 6 of 6 designs, most often 453 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ENpin 1 | Connected to: 5V 67% · a signal 33% | — |
| GNDpin 2 | Connected to: GND 100% | — |
| SWpin 3 | Connected to: Signal 100% |
|
| VINpin 4 | Connected to: 5V 83% · a signal 17% |
|
| FBpin 5 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Basic ecp5-pcb by mattvenn, MioLink by Misaka0x2730, NX-ISD by Ghost3379 and IV6Clock2 base by SarahAlroe.
The TLV62568DBV in open source designs
The gallery holds 8 open source boards using the TLV62568DBV from 6 GitHub repositories; a typical one measures about 99.5 × 80.8 mm and carries around 111 components.
75% use four copper layers or more, and 50% carry an open source license.
The most starred is Basic ecp5-pcb by mattvenn.
Microcontrollers on boards using the TLV62568DBV
What boards using the TLV62568DBV are built for
TLV62568DBV: common questions
Where can I find a TLV62568DBV reference design?
Each of the 8 boards on this page is a real design using the TLV62568DBV. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TLV62568DBV SW pin connected?
The SW pin has a inductor on 6 of 6 designs, most often 2.2 µH (then 1 µH). Counted from the KiCad layouts of 6 open source designs using the TLV62568DBV.
What decoupling capacitors do designs use on the TLV62568DBV VIN pin?
The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 4.7 µF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the TLV62568DBV.
What resistor goes on the TLV62568DBV FB pin?
The FB pin has a resistor to GND on 6 of 6 designs, most often 100 kΩ (then 120 kΩ). Counted from the KiCad layouts of 6 open source designs using the TLV62568DBV.
Which microcontrollers do boards using the TLV62568DBV use?
Most are built on AVR/Arduino (1), ESP32 (1), FPGA (1) and RP2040/RP2350 (1).
How big is a typical board using the TLV62568DBV?
The median is 99.5 × 80.8 mm, and 25% are two-layer designs.
What is the most popular open source board using the TLV62568DBV?
By GitHub stars, Basic ecp5-pcb by mattvenn, with 143 stars.
Can I simulate one of these boards using the TLV62568DBV before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.