7 open source boards using the TLV9064IPWR
Real designs built with the TLV9064IPWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Radiohat 2.0 Preliminary (not a Hat)
mpvano
85 × 56 mm153 parts4LMIT2STM32
Cc glasses
noahzhy
152.3 × 72 mm153 parts4LMIT1RP2040/RP2350
Nbfm1-open bci
C31N
190 × 110 mm640 parts4LNo license0AGBM-02 AA 1-1
AnasSarkiz
131.3 × 72.4 mm200 parts4LCC-BY-SA-4.00Nordic nRF
Smartbag core
claudiofin
196 × 20 mm107 parts6LMIT0STM32
Sutterspeed
StaRadian
36 × 12.8 mm33 parts4LNo license0- schematic only · 278 parts
Dc cv interface
jounih
278 partsMIT0
How designs wire the TLV9064IPWR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TLV9064IPWR connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 5 of 6 designs, most often 10 kΩ (then 8.2 kΩ).
- The V+ pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 1 µF).
- Pin 8 has a series resistor on 5 of 6 designs, most often 30 kΩ (then 5.1 kΩ).
- The V- pin is tied to GND on 6 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| -pin 2, 6, 9, 13 | Connected to: Signal 100% |
|
| +pin 3, 5, 10, 12 | Connected to: Signal 67% · 1.65V 33% |
|
| V+pin 4 | Connected to: 3.3V 67% · a signal 33% |
|
| Pin 7 | Connected to: Signal 100% |
|
| Pin 8 | Connected to: Signal 100% |
|
| V-pin 11 | Connected to: GND 100% | — |
| Pin 14 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Radiohat 2.0 Preliminary (not a Hat) by mpvano, Cc glasses by noahzhy, AGBM-02 AA 1-1 by AnasSarkiz and Nbfm1-open bci by C31N.
The TLV9064IPWR in open source designs
The gallery holds 7 open source boards using the TLV9064IPWR from 7 GitHub repositories; a typical one measures about 141.8 × 64 mm and carries around 153 components.
100% use four copper layers or more, and 71% carry an open source license.
The most starred is Radiohat 2.0 Preliminary (not a Hat) by mpvano.
Parts used alongside the TLV9064IPWR
Microcontrollers on boards using the TLV9064IPWR
What boards using the TLV9064IPWR are built for
TLV9064IPWR: common questions
Where can I find a TLV9064IPWR reference design?
Each of the 7 boards on this page is a real design using the TLV9064IPWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TLV9064IPWR - pin?
The - pins have a series resistor on 5 of 6 designs, most often 10 kΩ (then 8.2 kΩ). Counted from the KiCad layouts of 6 open source designs using the TLV9064IPWR.
What decoupling capacitors do designs use on the TLV9064IPWR V+ pin?
The V+ pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the TLV9064IPWR.
What resistor goes on the TLV9064IPWR pin 8?
Pin 8 has a series resistor on 5 of 6 designs, most often 30 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 6 open source designs using the TLV9064IPWR.
Which microcontrollers do boards using the TLV9064IPWR use?
Most are built on STM32 (2), Nordic nRF (1) and RP2040/RP2350 (1).
How big is a typical board using the TLV9064IPWR?
The median is 141.8 × 64 mm, and 0% are two-layer designs.
What is the most popular open source board using the TLV9064IPWR?
By GitHub stars, Radiohat 2.0 Preliminary (not a Hat) by mpvano, with 2 stars.
Can I simulate one of these boards using the TLV9064IPWR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.