6 open source boards using the TPS2115ADRBR
Real designs built with the TPS2115ADRBR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
VCAT-VehicleControlUnit
lhr-solar
86.6 × 71.8 mm122 parts2LMIT2TI MSP430/CC
PROC091G
um-kiho
115.3 × 25.3 mm440 parts8LNo license0STM32
EPS
MatthiasGeorgImhof
80 × 80 mm238 parts4LCC-BY-NC-4.00STM32
PS-HVCarrier
lhr-solar
80.5 × 84.7 mm152 parts2LNo license0Electronics
QuadFlyController
45 × 45 mm60 parts4LMIT0TI MSP430/CC
PROC091F
um-kiho
1.9 × 1.9 mm414 parts8LNo license0
How designs wire the TPS2115ADRBR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPS2115ADRBR connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 5 of 5 designs, most often 1 kΩ (then 332 Ω).
- The OUT pin is tied to 5V on 5 of 5 designs.
- The EXP pin is tied to GND on 5 of 5 designs.
- The STAT pin has a pull-up to 5V on 3 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| STATpin 1 | Connected to: Signal 80% · not connected 20% |
|
| D0pin 2 | Connected to: Not connected 60% · a signal 40% | — |
| D1pin 3 | Connected to: GND 60% · a signal 40% | — |
| ILIMpin 4 | Connected to: Signal 100% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| IN2pin 6 | Connected to: 5V 60% · a signal 40% | — |
| OUTpin 7 | Connected to: 5V 100% | — |
| IN1pin 8 | Connected to: 5V 60% · a signal 40% |
|
| EXPpin 9 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include VCAT-VehicleControlUnit by lhr-solar, PS-HVCarrierPCB by lhr-solar, EPS by MatthiasGeorgImhof and Electronics by QuadFlyController.
The TPS2115ADRBR in open source designs
The gallery holds 6 open source boards using the TPS2115ADRBR from 5 GitHub repositories; a typical one measures about 80.3 × 58.4 mm and carries around 195 components.
67% use four copper layers or more, and 33% carry an open source license.
The most starred is VCAT-VehicleControlUnit by lhr-solar.
Parts used alongside the TPS2115ADRBR
Microcontrollers on boards using the TPS2115ADRBR
What boards using the TPS2115ADRBR are built for
TPS2115ADRBR: common questions
Where can I find a TPS2115ADRBR reference design?
Each of the 6 boards on this page is a real design using the TPS2115ADRBR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS2115ADRBR ILIM pin?
The ILIM pin has a resistor to GND on 5 of 5 designs, most often 1 kΩ (then 332 Ω). Counted from the KiCad layouts of 5 open source designs using the TPS2115ADRBR.
How is the TPS2115ADRBR OUT pin connected?
The OUT pin is tied to 5V on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TPS2115ADRBR.
How is the TPS2115ADRBR EXP pin connected?
The EXP pin is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TPS2115ADRBR.
Which microcontrollers do boards using the TPS2115ADRBR use?
Most are built on STM32 (2), TI MSP430/CC (2) and ESP32 (1).
How big is a typical board using the TPS2115ADRBR?
The median is 80.3 × 58.4 mm, and 33% are two-layer designs.
What is the most popular open source board using the TPS2115ADRBR?
By GitHub stars, VCAT-VehicleControlUnit by lhr-solar, with 2 stars.
Can I simulate one of these boards using the TPS2115ADRBR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.