7 open source boards using the TPS22810DRVR

Real designs built with the TPS22810DRVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the TPS22810DRVR

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS22810DRVR connects to, and the resistors, capacitors and other passives placed on it.

  • The CT pin has a capacitor to GND on 5 of 6 designs, most often 10 nF (then 100 nF).
  • The VIN pin has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 1 µF).
  • The VOUT pin has a capacitor to GND on 4 of 6 designs, most often 100 nF (then 330 µF).
VOUTpin 1Connected to: A connector 50% · VCC_P 17%
  • Capacitor to GND on 67% · 100 nF (6), 330 µF (4), 10 µF (2)
QODpin 2Connected to: Signal 67% · not connected 33%
  • Capacitor to GND on 33% · 100 nF (2), 10 µF (2), 1 µF (2)
CTpin 3Connected to: Signal 83% · GND 17%
  • Capacitor to GND on 83% · 10 nF (3), 100 nF (2)
GNDpin 4, 7Connected to: GND 100%
EN/UVLOpin 5Connected to: The microcontroller 33%, a connector 33% · VCC_P_EN 17%
  • Resistor to GND on 33% · 4.7 kΩ (1), 100 kΩ (1)
  • Capacitor to GND on 33% · 100 nF (1), 10 µF (1)
VINpin 6Connected to: A connector 33% · VCC 33%
  • Capacitor to GND on 83% · 100 nF (6), 1 µF (5), 10 µF (3)
  • Series resistor on 33% · 3.3 kΩ (2), 20 mΩ (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Eps by OSUSat, Hoerbaer by drachosaurus, Qcomlt debugboard by CodeLinaro-mirror and RTB D15 by git4dcc.

The TPS22810DRVR in open source designs

The gallery holds 7 open source boards using the TPS22810DRVR from 6 GitHub repositories; a typical one measures about 76 × 69.6 mm and carries around 195 components.

86% use four copper layers or more, and 71% carry an open source license.

The most starred is Eps by OSUSat.

Microcontrollers on boards using the TPS22810DRVR

TPS22810DRVR: common questions

Where can I find a TPS22810DRVR reference design?

Each of the 7 boards on this page is a real design using the TPS22810DRVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS22810DRVR CT pin connected?

The CT pin has a capacitor to GND on 5 of 6 designs, most often 10 nF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the TPS22810DRVR.

How is the TPS22810DRVR VIN pin connected?

The VIN pin has a capacitor to GND on 5 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the TPS22810DRVR.

How is the TPS22810DRVR VOUT pin connected?

The VOUT pin has a capacitor to GND on 4 of 6 designs, most often 100 nF (then 330 µF). Counted from the KiCad layouts of 6 open source designs using the TPS22810DRVR.

Which microcontrollers do boards using the TPS22810DRVR use?

Most are built on ESP32 (3), Microchip SAM (1) and STM32 (1).

How big is a typical board using the TPS22810DRVR?

The median is 76 × 69.6 mm, and 14% are two-layer designs.

What is the most popular open source board using the TPS22810DRVR?

By GitHub stars, Eps by OSUSat, with 8 stars.

Can I simulate one of these boards using the TPS22810DRVR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part