8 open source boards using the TPS2561
Real designs built with the TPS2561, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
QSIC
dabridgham
214.1 × 131.8 mm174 parts4LNo license11Reform2-motherboard30
owebeeone
276 × 93.5 mm513 parts6LNo license0FPGA
USIC
dabridgham
214.1 × 265.6 mm245 parts6LNo license0Oel usb-3-hub
OpenElectronicsLab
50 × 40 mm108 parts2LNo license0GigaHub
Keyaan-07
61.4 × 45.8 mm65 parts4LMIT0- schematic only · 939 partsESP32
Mechpad
AdriTeixeHax
939 parts2LNo license0 Cnc hmi usb power
tangentaudio
88.9 × 76.2 mm95 parts2LNo license3Reform2-motherboard
owebeeone
276 × 93.5 mm501 parts6LNo license0
How designs wire the TPS2561
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS2561 connects to, and the resistors, capacitors and other passives placed on it.
- The ILM pin has a resistor to GND on 6 of 6 designs, most often 56.2 kΩ (then 25.5 kΩ).
- The IN pins is tied to 5V on 83% of them (a signal on 2).
- The FAULT2 pin has a pull-up to 5V on 4 of 6 designs, most often 100 kΩ (then 10 kΩ).
- The OUT2 pin has a capacitor to GND on 4 of 6 designs, most often 150 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| INpin 2, 3 | Connected to: 5V 83% · a signal 17% | — |
| EN1pin 4 | Connected to: TUSB8041 33% · GND 33% |
|
| EN2pin 5 | Connected to: USB3340 33%, TUSB8041 33% |
|
| FAULT2pin 6 | Connected to: Signal 83% · not connected 17% |
|
| ILMpin 7 | Connected to: Signal 100% |
|
| OUT2pin 8 | Connected to: A connector 33% · VBUS_2 17% |
|
| OUT1pin 9 | Connected to: Signal 50% · not connected 33% · VBUS_1 17% |
|
| FAULT1pin 10 | Connected to: Signal 83% · not connected 17% |
|
| PADpin 11 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include QSIC by dabridgham, Cnc hmi usb power by tangentaudio, USIC by dabridgham and GigaHub by Keyaan-07.
The TPS2561 in open source designs
The gallery holds 8 open source boards using the TPS2561 from 7 GitHub repositories; a typical one measures about 214.1 × 93.5 mm and carries around 210 components.
63% use four copper layers or more, and 13% carry an open source license.
The most starred is QSIC by dabridgham.
Parts used alongside the TPS2561
What boards using the TPS2561 are built for
TPS2561: common questions
Where can I find a TPS2561 reference design?
Each of the 8 boards on this page is a real design using the TPS2561. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS2561 ILM pin?
The ILM pin has a resistor to GND on 6 of 6 designs, most often 56.2 kΩ (then 25.5 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS2561.
How is the TPS2561 IN pin connected?
The IN pins is tied to 5V on 83% of them (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the TPS2561.
What pull-up resistor is used on the TPS2561 FAULT2 pin?
The FAULT2 pin has a pull-up to 5V on 4 of 6 designs, most often 100 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS2561.
What parts are used alongside the TPS2561?
The IS43TR16128B, MAX3033E, TPS82085, TUSB8041 and USB3340 appear in the most repositories here.
Which microcontrollers do boards using the TPS2561 use?
Most are built on FPGA (2) and ESP32 (1).
How big is a typical board using the TPS2561?
The median is 214.1 × 93.5 mm, and 38% are two-layer designs.
What is the most popular open source board using the TPS2561?
By GitHub stars, QSIC by dabridgham, with 11 stars.
Can I simulate one of these boards using the TPS2561 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.