9 open source boards using the TPS25730DREFR
Real designs built with the TPS25730DREFR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Flatburn lte
MIT-Senseable-City-Lab
130 × 125 mm542 parts4LMIT1Nordic nRF
FindMyCharger
dave9123
74 × 56 mm189 parts4LNo license1ESP32
BeeFASYER SPARROW
beewarden
64.1 × 72.8 mm121 parts4LCERN-OHL-S-2.01Reform2-motherboard30
owebeeone
276 × 93.5 mm513 parts6LNo license0STM32
CANSAT-M2-2026
Engineer162
55 × 100 mm156 parts4LCERN-OHL-S-2.00- schematic only · 44 partsESP32
Fandom
tfindlay-au
44 partsNo license0 Pd booster-16amps
mikegoelzer
45.6 × 131 mm82 parts4LCustom license0EGSE2
parsa-novin
101.6 × 81.3 mm79 parts4LNo license2Bustingballscrazystylenolube
parsa-novin
101.6 × 81.3 mm73 parts2LNo license2
How designs wire the TPS25730DREFR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS25730DREFR connects to, and the resistors, capacitors and other passives placed on it.
- The CC1 pin has a capacitor to GND on 7 of 7 designs, most often 330 pF.
- The CC2 pin has a capacitor to GND on 7 of 7 designs, most often 330 pF.
- The VIN_3V3 pin has a decoupling capacitor on 7 of 7 designs, most often 10 µF (then 100 nF).
- The LDO_3V3 pin has a series resistor on 6 of 7 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| LDO_3V3pin 1 | Connected to: Signal 86% |
|
| ADCIN1pin 2 | Connected to: Signal 57% · GND 43% |
|
| ADCIN2pin 3 | Connected to: Signal 100% |
|
| LDO_1V5pin 4 | Connected to: Signal 71% |
|
| ADCIN3pin 5 | Connected to: Signal 86% |
|
| ADCIN4pin 7 | Connected to: Signal 100% |
|
| I2CT_SDApin 8 | Connected to: A connector 29%, BQ25798RQMR 29%, the microcontroller 29% |
|
| I2CT_SCLpin 9 | Connected to: A connector 29%, BQ25798RQMR 29%, the microcontroller 29% |
|
| GND_1pin 11 | Connected to: GND 100% | — |
| GND_2pin 12 | Connected to: GND 100% | — |
| PLUG_FLIPpin 13 | Connected to: Not connected 71% · a signal 29% | — |
| GND_3pin 14 | Connected to: GND 100% | — |
| DRAIN_1pin 15 | Connected to: Not connected 100% | — |
| GND_4pin 16 | Connected to: GND 100% | — |
| GND_5pin 17 | Connected to: GND 100% | — |
| FAULT_INpin 18 | Connected to: Signal 71% · not connected 29% |
|
| PPHV_1pin 20 | Connected to: BQ25798RQMR 29% |
|
| PPHV_2pin 21 | Connected to: BQ25798RQMR 29% |
|
| PPHV_3pin 22 | Connected to: BQ25798RQMR 29% |
|
| VBUS_IN_1pin 23 | Connected to: VBUS 86% |
|
| VBUS_IN_2pin 24 | Connected to: VBUS 86% |
|
| VBUS_IN_3pin 25 | Connected to: VBUS 86% |
|
| RESERVED_1pin 26 | Connected to: Signal 71% |
|
| RESERVED_2pin 27 | Connected to: Signal 71% |
|
| CC1pin 28 | Connected to: A connector 100% |
|
| CC2pin 29 | Connected to: A connector 100% |
|
| DRAIN_2pin 30 | Connected to: Not connected 100% | — |
| GND_6pin 31 | Connected to: GND 100% | — |
| VBUS_1pin 32 | Connected to: VBUS 86% |
|
| VBUS_2pin 33 | Connected to: VBUS 86% |
|
| GND_7pin 34 | Connected to: GND 100% | — |
| GND_8pin 35 | Connected to: GND 100% | — |
| RESERVED_3pin 36 | Connected to: Signal 71% |
|
| VIN_3V3pin 38 | Connected to: 3.3V 57% · a signal 43% |
|
| GND_9pin 39 | Connected to: GND 100% | — |
| DRAIN_3pin 40 | Connected to: Not connected 100% | — |
| PPHV_4pin 41 | Connected to: Not connected 40% · VIN 20% · a signal 40% |
|
| VBUS_IN_4pin 42 | Connected to: Not connected 40% · VBUS_IN_POST_SHUNT 40% · a signal 20% |
|
| VBUS_3pin 43 | Connected to: Not connected 40% · VBUS_IN_POST_SHUNT 40% · a signal 20% |
|
| GND_10pin 44 | Connected to: GND 60% · not connected 40% | — |
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bustingballscrazystylenolube by parsa-novin, BeeFASYER SPARROW by beewarden, FindMyCharger by dave9123 and Flatburn lte by MIT-Senseable-City-Lab.
The TPS25730DREFR in open source designs
The gallery holds 9 open source boards using the TPS25730DREFR from 8 GitHub repositories; a typical one measures about 87.8 × 87.4 mm and carries around 121 components.
88% use four copper layers or more, and 33% carry an open source license.
The most starred is EGSE2 by parsa-novin.
Parts used alongside the TPS25730DREFR
Microcontrollers on boards using the TPS25730DREFR
What boards using the TPS25730DREFR are built for
TPS25730DREFR: common questions
Where can I find a TPS25730DREFR reference design?
Each of the 9 boards on this page is a real design using the TPS25730DREFR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS25730DREFR CC1 pin connected?
The CC1 pin has a capacitor to GND on 7 of 7 designs, most often 330 pF. Counted from the KiCad layouts of 7 open source designs using the TPS25730DREFR.
How is the TPS25730DREFR CC2 pin connected?
The CC2 pin has a capacitor to GND on 7 of 7 designs, most often 330 pF. Counted from the KiCad layouts of 7 open source designs using the TPS25730DREFR.
What decoupling capacitors do designs use on the TPS25730DREFR VIN_3V3 pin?
The VIN_3V3 pin has a decoupling capacitor on 7 of 7 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the TPS25730DREFR.
Which microcontrollers do boards using the TPS25730DREFR use?
Most are built on ESP32 (2), Nordic nRF (1) and STM32 (1).
How big is a typical board using the TPS25730DREFR?
The median is 87.8 × 87.4 mm, and 13% are two-layer designs.
What is the most popular open source board using the TPS25730DREFR?
By GitHub stars, EGSE2 by parsa-novin, with 2 stars.
Can I simulate one of these boards using the TPS25730DREFR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.