7 open source boards using the TPS27081ADDCR

Real designs built with the TPS27081ADDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the TPS27081ADDCR

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS27081ADDCR connects to, and the resistors, capacitors and other passives placed on it.

  • The R1/C1 pin has a pull-up to 5V on 6 of 7 designs, most often 10 kΩ (then 100 kΩ).
  • The VIN pin has a decoupling capacitor on 5 of 7 designs, most often 22 µF (then 100 nF).
  • The R2 pin has a resistor to GND on 4 of 7 designs, most often 1 kΩ.
  • The VOUT pins have a capacitor to GND on 4 of 7 designs, most often 100 nF (then 2.2 µF).
R2pin 1Connected to: Signal 57% · GND 43%
  • Resistor to GND on 57% · 1 kΩ (4)
VOUTpin 2, 3Connected to: A connector 21% · BATT 29%
  • Capacitor to GND on 57% · 100 nF (8), 2.2 µF (4), 1 µF (2)
VINpin 4Connected to: 5V 86%
  • Decoupling capacitor on 71% · 22 µF (4), 100 nF (1), 1 µF (1)
ON/OFFpin 5Connected to: The microcontroller 57%
  • Resistor to GND on 43% · 10 kΩ (3)
R1/C1pin 6Connected to: Signal 100%
  • Pull-up to 5V on 86% · 10 kΩ (5), 100 kΩ (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include One air max by claynicholson, EPS v1 by Migsster, Moisture sensor hardware by IMHarris and VoidLens-DIY-VR-Headset-V2 by scattercat-123.

The TPS27081ADDCR in open source designs

The gallery holds 7 open source boards using the TPS27081ADDCR from 7 GitHub repositories; a typical one measures about 90.1 × 72 mm and carries around 79 components.

57% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.

The most starred is One air max by claynicholson.

Microcontrollers on boards using the TPS27081ADDCR

What boards using the TPS27081ADDCR are built for

TPS27081ADDCR: common questions

Where can I find a TPS27081ADDCR reference design?

Each of the 7 boards on this page is a real design using the TPS27081ADDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the TPS27081ADDCR R1/C1 pin?

The R1/C1 pin has a pull-up to 5V on 6 of 7 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 7 open source designs using the TPS27081ADDCR.

What decoupling capacitors do designs use on the TPS27081ADDCR VIN pin?

The VIN pin has a decoupling capacitor on 5 of 7 designs, most often 22 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the TPS27081ADDCR.

What resistor goes on the TPS27081ADDCR R2 pin?

The R2 pin has a resistor to GND on 4 of 7 designs, most often 1 kΩ. Counted from the KiCad layouts of 7 open source designs using the TPS27081ADDCR.

What parts are used alongside the TPS27081ADDCR?

The AT24CM02-SSHD-B, BQ7790512PWR, ESP32-C6-WROOM-1-N8, TPL5010DDCR and TPS2117DRLR_C22399676 appear in the most repositories here.

Which microcontrollers do boards using the TPS27081ADDCR use?

Most are built on ESP32 (3), AVR/Arduino (1), RP2040/RP2350 (1) and STM32 (1).

How big is a typical board using the TPS27081ADDCR?

The median is 90.1 × 72 mm, and 57% are two-layer designs.

What is the most popular open source board using the TPS27081ADDCR?

By GitHub stars, One air max by claynicholson, with 102 stars.

Can I simulate one of these boards using the TPS27081ADDCR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part