29 open source boards using the ESP32-C6-WROOM-1-N8
Real designs built with the ESP32-C6-WROOM-1-N8, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
One air max
claynicholson
99.5 × 72 mm197 parts4LMIT102ESP32
EverAliveSensor
jfm92
64 × 50 mm50 parts2LCC-BY-NC-4.027ESP32
InkCard
Irony95
62.4 × 113.8 mm84 parts2LMIT11ESP32
SCAN
jjsprandel
153.3 × 53 mm181 parts6LCC-BY-NC-4.01ESP32
Eveningstar hardware
ciaassured
81.2 × 71.6 mm120 parts2LAGPL-3.01ESP32
Msxnano dock
Papipapito
120 × 70 mm85 parts2LNo license1ESP32
PCB
SIMCA-USI
60.7 × 60.7 mm51 parts2LNo license1ESP32
AgriPV-Messstation
DerSchweigefuchs
113 × 113 mm238 parts4LNo license0ESP32
Pcb openair max main
Open-Air-Foundation
99.5 × 72 mm235 parts4LCC-BY-SA-4.00ESP32
Esp32-led matrix
n2048-creative-technology
58.1 × 41.8 mm147 parts2LNo license0ESP32
Waypoint
M-Mrk
140 × 80 mm129 parts4LNo license0ESP32
Smart iv monitor
kylepretty
79.5 × 83.8 mm106 parts2LNo license0ESP32
Controller
micthiesen
150 × 110 mm99 parts4LNo license0ESP32
Prod pdu
vd-rd
141 × 40 mm95 parts2LNo license0ESP32
Thermostat
Connicpu
140 × 64 mm92 parts2LMIT0ESP32
Heating controller
Zepheus
160 × 95 mm92 parts2LMIT0ESP32
Ummon
JonaWe
60 × 60 mm75 parts4LNo license0ESP32
Woow zigbee fresh air
WOOWTECH
63.4 × 83.1 mm68 parts2LNo license0ESP32
SolarDataLogger
brokebit
90 × 90 mm64 parts6LCC0-1.00ESP32
MitsubishiSC
loozhengyuan
50 × 43 mm60 parts6LMIT0ESP32
Panasonic intellibalance esphome
lukewaite
110 × 56 mm55 parts2LNo license0ESP32
Tix clock
connorslade
139 × 40 mm50 parts2LNo license0ESP32
Esp32-c3-led controller
n2048-creative-technology
20.5 × 35.5 mm20 parts2LNo license0- schematic only · 86 partsESP32
Coffee
brensch
86 partsNo license0 - schematic only · 40 partsESP32
Esp32-marine sensorhub v2
dpmcgarry
40 parts2LCERN-OHL-S-2.00 ESP32
SCAN mainboard
jjsprandel
100 × 70 mm54 parts2LCC-BY-NC-4.01ESP32
PCB sinplanos
SIMCA-USI
60.7 × 60.7 mm51 parts2LNo license1ESP32
Placed
Zepheus
160 × 95 mm92 parts2LMIT0ESP32
Roomnode c6
AskAlice
55 × 45 mm27 parts2LNo license0
How designs wire the ESP32-C6-WROOM-1-N8
Read from the KiCad layouts of 23 open source designs, one per repository: what each pin of the ESP32-C6-WROOM-1-N8 connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin has a capacitor to GND on 22 of 23 designs, most often 1 µF (then 100 nF).
- The EN pin has a pull-up to 3.3V on 21 of 23 designs, most often 10 kΩ (then 100 kΩ).
- The 3V3 pin is tied to 3.3V on 22 of 23 designs.
- The IO8 pin has a pull-up to 3.3V on 16 of 23 designs, most often 10 kΩ (then 3.3 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37 | Connected to: GND 95% | — |
| 3V3pin 2 | Connected to: 3.3V 96% | — |
| ENpin 3 | Connected to: Signal 96% |
|
| IO6pin 6 | Connected to: A connector 26% · not connected 22% |
|
| IO7pin 7 | Connected to: A connector 26% · not connected 17% |
|
| IO0pin 8 | Connected to: Signal 74% · not connected 26% |
|
| IO8pin 10 | Connected to: Signal 87% |
|
| IO12pin 13 | Connected to: A connector 22% |
|
| IO13pin 14 | Connected to: A connector 22% |
|
| IO9pin 15 | Connected to: A connector 22% |
|
| NCpin 22 | Connected to: Not connected 100% | — |
16 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include One air max by claynicholson, EverAliveSensor by jfm92, InkCard by Irony95 and Eveningstar hardware by ciaassured.
The ESP32-C6-WROOM-1-N8 in open source designs
The gallery holds 29 open source boards using the ESP32-C6-WROOM-1-N8 from 26 GitHub repositories; a typical one measures about 99.4 × 70 mm and carries around 85 components.
68% are two-layer designs, the rest use four layers or more, and 34% carry an open source license.
The most starred is One air max by claynicholson.
Parts used alongside the ESP32-C6-WROOM-1-N8
Microcontrollers on boards using the ESP32-C6-WROOM-1-N8
What boards using the ESP32-C6-WROOM-1-N8 are built for
ESP32-C6-WROOM-1-N8: common questions
Where can I find a ESP32-C6-WROOM-1-N8 reference design?
Each of the 29 boards on this page is a real design using the ESP32-C6-WROOM-1-N8. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP32-C6-WROOM-1-N8 EN pin connected?
The EN pin has a capacitor to GND on 22 of 23 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 23 open source designs using the ESP32-C6-WROOM-1-N8.
How is the ESP32-C6-WROOM-1-N8 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 22 of 23 designs. Counted from the KiCad layouts of 23 open source designs using the ESP32-C6-WROOM-1-N8.
What pull-up resistor is used on the ESP32-C6-WROOM-1-N8 IO8 pin?
The IO8 pin has a pull-up to 3.3V on 16 of 23 designs, most often 10 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 23 open source designs using the ESP32-C6-WROOM-1-N8.
What parts are used alongside the ESP32-C6-WROOM-1-N8?
The AMS1117-3.3, USBLC6-2SC6, AP63203WU-7, AMS1117-3.3(TO-252) and AT24CM02-SSHD-B appear in the most repositories here.
Which microcontrollers do boards using the ESP32-C6-WROOM-1-N8 use?
Most are built on ESP32 (29).
How big is a typical board using the ESP32-C6-WROOM-1-N8?
The median is 99.4 × 70 mm, and 68% are two-layer designs.
What is the most popular open source board using the ESP32-C6-WROOM-1-N8?
By GitHub stars, One air max by claynicholson, with 102 stars.
Can I simulate one of these boards using the ESP32-C6-WROOM-1-N8 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.