11 open source boards using the TPL5010DDCR
Real designs built with the TPL5010DDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
One air max
claynicholson
99.5 × 72 mm197 parts4LMIT102STM32
EcoApi BeeHiveMonitoring
EcoApi
90.6 × 58 mm166 parts2LGPL-3.04STM32
EPS
MatthiasGeorgImhof
80 × 80 mm238 parts4LCC-BY-NC-4.00ESP32
Pcb openair max main
Open-Air-Foundation
99.5 × 72 mm235 parts4LCC-BY-SA-4.00STM32
Default
RileyLeff
100 × 65 mm234 parts6LNo license0TI MSP430/CC
Pco2-sensor board
NOAA-PMEL
101.6 × 76.2 mm147 parts4LBSD-3-Clause0ESP32
Airgradient-GO
Open-Air-Foundation
62.9 × 87 mm141 parts4LCC-BY-SA-4.00RP2040/RP2350
EWP-Control
haum2002
76 × 64 mm93 parts4LNo license0STM32
Default.active pre v0.2-hydration
RileyLeff
100 × 65 mm234 parts6LNo license0STM32
Default.shipped v0.1
RileyLeff
100 × 65 mm234 parts6LNo license0STM32
AVIONICS BOARD
MatthiasGeorgImhof
80 × 80 mm178 parts4LCC-BY-NC-4.00
How designs wire the TPL5010DDCR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the TPL5010DDCR connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 1 µF).
- The DELAY/M_RST pin has a resistor to GND on 6 of 8 designs, most often 51 kΩ (then 22 kΩ).
- The RST pin has a pull-up to 3.3V on 5 of 8 designs, most often 100 kΩ (then 10 kΩ).
- The WAKE pin is left unconnected on 5 of 8 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 75% · a signal 25% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| DELAY/M_RSTpin 3 | Connected to: Signal 88% |
|
| WAKEpin 5 | Connected to: Not connected 63% · a signal 38% | — |
| RSTpin 6 | Connected to: The microcontroller 63% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include One air max by claynicholson, EcoApi BeeHiveMonitoring by EcoApi, EWP-Control by haum2002 and AVIONICS BOARD by MatthiasGeorgImhof.
The TPL5010DDCR in open source designs
The gallery holds 11 open source boards using the TPL5010DDCR from 8 GitHub repositories; a typical one measures about 99.4 × 72 mm and carries around 197 components.
91% use four copper layers or more, and 45% carry an open source license.
The most starred is One air max by claynicholson.
Parts used alongside the TPL5010DDCR
Microcontrollers on boards using the TPL5010DDCR
What boards using the TPL5010DDCR are built for
TPL5010DDCR: common questions
Where can I find a TPL5010DDCR reference design?
Each of the 11 boards on this page is a real design using the TPL5010DDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TPL5010DDCR VDD pin?
The VDD pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 8 open source designs using the TPL5010DDCR.
What resistor goes on the TPL5010DDCR DELAY/M_RST pin?
The DELAY/M_RST pin has a resistor to GND on 6 of 8 designs, most often 51 kΩ (then 22 kΩ). Counted from the KiCad layouts of 8 open source designs using the TPL5010DDCR.
What pull-up resistor is used on the TPL5010DDCR RST pin?
The RST pin has a pull-up to 3.3V on 5 of 8 designs, most often 100 kΩ (then 10 kΩ). Counted from the KiCad layouts of 8 open source designs using the TPL5010DDCR.
What parts are used alongside the TPL5010DDCR?
The AT24CM02-SSHD-B, BME280, BQ7790512PWR, ESP32-C6-WROOM-1-N8 and INA226AIDGSR appear in the most repositories here.
Which microcontrollers do boards using the TPL5010DDCR use?
Most are built on STM32 (6), ESP32 (3), RP2040/RP2350 (1) and TI MSP430/CC (1).
How big is a typical board using the TPL5010DDCR?
The median is 99.4 × 72 mm, and 9% are two-layer designs.
What is the most popular open source board using the TPL5010DDCR?
By GitHub stars, One air max by claynicholson, with 102 stars.
Can I simulate one of these boards using the TPL5010DDCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.