12 open source boards using the TPS54360DDAR
Real designs built with the TPS54360DDAR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
EtherCATControllerHP
kscalelabs
77 × 77 mm168 parts6LNo license5Nanoleaf-Shapes controller
Cptmeme
35.6 × 21.5 mm42 parts2LGPL-3.03STM32
AEM-60DC8 V1.2
akhemka-cmd
122 × 87.6 mm350 parts2LNo license0ESP32
Ptz driver
Aottens
100 × 80 mm251 parts4LNo license0ESP32
Vancontroller
Camperlux
230 × 135 mm247 parts4LCustom license0STM32
Kurc f405
ganymede451
39.9 × 39.9 mm78 parts4LNo license0EtherCATControllerLP
kscalelabs
50 × 50 mm167 parts6LNo license5FPGA
LightRail Eval Board
lightrail-dev
100 × 100 mm187 parts22LNo license1ESP32
Rev a input
Aottens
100 × 80 mm251 parts4LNo license0NXP
SpriteHardware
akhemka-cmd
130.8 × 89.9 mm109 parts4LNo license0STM32
EtherCATSTM32
kscalelabs
50 × 50 mm157 parts6LNo license5Test3
pginfinitylab-ai
50 × 40 mm24 parts2LNo license0
How designs wire the TPS54360DDAR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS54360DDAR connects to, and the resistors, capacitors and other passives placed on it.
- The BOOT_1 pin has a series capacitor on 7 of 7 designs, most often 100 nF.
- The RT/CLK_4 pin has a resistor to GND on 7 of 7 designs, most often 162 kΩ (then 330 kΩ).
- The FB_5 pin has a resistor to GND on 7 of 7 designs, most often 10 kΩ (then 10.2 kΩ).
- The COMP_6 pin has a capacitor to GND on 7 of 7 designs, most often 47 pF (then 39 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BOOT_1pin 1 | Connected to: Signal 100% |
|
| VIN_2pin 2 | Connected to: 42V 71% · a signal 29% |
|
| EN_3pin 3 | Connected to: Not connected 71% · a signal 29% | — |
| RT/CLK_4pin 4 | Connected to: Signal 100% |
|
| FB_5pin 5 | Connected to: Signal 100% |
|
| COMP_6pin 6 | Connected to: Signal 100% |
|
| GND_7pin 7 | Connected to: GND 100% | — |
| SW_8pin 8 | Connected to: Signal 100% |
|
| GNDPADpin 9 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EtherCATControllerHP by kscalelabs, Nanoleaf-Shapes controller by Cptmeme, AEM-60DC8 V1.2 by akhemka-cmd and Ptz driver by Aottens.
The TPS54360DDAR in open source designs
The gallery holds 12 open source boards using the TPS54360DDAR from 8 GitHub repositories; a typical one measures about 88.5 × 78.5 mm and carries around 168 components.
75% use four copper layers or more, and 8% carry an open source license.
The most starred is EtherCATControllerHP by kscalelabs.
Parts used alongside the TPS54360DDAR
What boards using the TPS54360DDAR are built for
TPS54360DDAR: common questions
Where can I find a TPS54360DDAR reference design?
Each of the 12 boards on this page is a real design using the TPS54360DDAR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS54360DDAR BOOT_1 pin connected?
The BOOT_1 pin has a series capacitor on 7 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the TPS54360DDAR.
What resistor goes on the TPS54360DDAR RT/CLK_4 pin?
The RT/CLK_4 pin has a resistor to GND on 7 of 7 designs, most often 162 kΩ (then 330 kΩ). Counted from the KiCad layouts of 7 open source designs using the TPS54360DDAR.
What resistor goes on the TPS54360DDAR FB_5 pin?
The FB_5 pin has a resistor to GND on 7 of 7 designs, most often 10 kΩ (then 10.2 kΩ). Counted from the KiCad layouts of 7 open source designs using the TPS54360DDAR.
What parts are used alongside the TPS54360DDAR?
The USBLC6-2SC6, AP2112K-3.3TRG1 and STM32F405RGT6 appear in the most repositories here.
Which microcontrollers do boards using the TPS54360DDAR use?
Most are built on STM32 (4), ESP32 (3), FPGA (1) and NXP (1).
How big is a typical board using the TPS54360DDAR?
The median is 88.5 × 78.5 mm, and 25% are two-layer designs.
What is the most popular open source board using the TPS54360DDAR?
By GitHub stars, EtherCATControllerHP by kscalelabs, with 5 stars.
Can I simulate one of these boards using the TPS54360DDAR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.