7 open source boards using the TPS55340RTER

Real designs built with the TPS55340RTER, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the TPS55340RTER

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS55340RTER connects to, and the resistors, capacitors and other passives placed on it.

  • The SW_1 pin has a inductor on 6 of 6 designs, most often 10 µH (then 74.4 GH).
  • The SS pin has a capacitor to GND on 6 of 6 designs, most often 47 nF (then 4.7 µF).
  • The COMP pin has a series resistor on 6 of 6 designs, most often 2 kΩ (then 2.49 kΩ).
  • The FREQ pin has a resistor to GND on 6 of 6 designs, most often 75 kΩ (then 78.7 kΩ).
SW_1pin 1Connected to: Signal 100%
  • Inductor on 100% · 10 µH (3), 74.4 GH (1)
VINpin 2Connected to: Signal 67% · 12V 33%
  • Capacitor to GND on 83% · 10 µF (3), 100 nF (3)
  • Inductor on 50% · 74.4 GH (1)
  • Series resistor on 33% · 100 kΩ (1), 0 Ω (1)
ENpin 3Connected to: 12V 67% · a signal 33%
  • Inductor on 33%
SSpin 4Connected to: Signal 100%
  • Capacitor to GND on 100% · 47 nF (4), 4.7 µF (1)
SYNCpin 5Connected to: GND 100%
AGNDpin 6Connected to: GND 100%
COMPpin 7Connected to: Signal 100%
  • Series resistor on 100% · 2 kΩ (2), 2.49 kΩ (1), 330 Ω (1)
  • Capacitor to GND on 50% · 100 pF (2)
FBpin 8Connected to: Signal 100%
  • Resistor to GND on 83% · 10 kΩ (4)
  • Pull-up to 30V on 67% · 237 kΩ (1), 250 kΩ (1), 86.6 kΩ (1)
  • Series resistor on 33% · 180 kΩ (1), 150 kΩ (1), 10 kΩ (1)
FREQpin 9Connected to: Signal 100%
  • Resistor to GND on 100% · 75 kΩ (3), 78.7 kΩ (2)
NC_10pin 10Connected to: GND 83% · not connected 17%
PGND_11pin 11Connected to: GND 100%
PGND_12pin 12Connected to: GND 100%
PGND_13pin 13Connected to: GND 100%
NC_14pin 14Connected to: GND 83% · not connected 17%
SW_15pin 15Connected to: Signal 100%
  • Inductor on 100% · 10 µH (3), 74.4 GH (1)
SW_16pin 16Connected to: Signal 100%
  • Inductor on 100% · 10 µH (3), 74.4 GH (1)
EP_17pin 17Connected to: GND 100%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Canjay by atopile, MG ZS V2 by damienmaguire, Electropulse by Shehroz30 and Ultrasonic Sound Steering - Driver Rev. C by kharper55.

The TPS55340RTER in open source designs

The gallery holds 7 open source boards using the TPS55340RTER from 6 GitHub repositories; a typical one measures about 90 × 83.5 mm and carries around 114 components.

86% use four copper layers or more, and 71% carry an open source license.

The most starred is Canjay by atopile.

Parts used alongside the TPS55340RTER

Microcontrollers on boards using the TPS55340RTER

What boards using the TPS55340RTER are built for

TPS55340RTER: common questions

Where can I find a TPS55340RTER reference design?

Each of the 7 boards on this page is a real design using the TPS55340RTER. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS55340RTER SW_1 pin connected?

The SW_1 pin has a inductor on 6 of 6 designs, most often 10 µH (then 74.4 GH). Counted from the KiCad layouts of 6 open source designs using the TPS55340RTER.

How is the TPS55340RTER SS pin connected?

The SS pin has a capacitor to GND on 6 of 6 designs, most often 47 nF (then 4.7 µF). Counted from the KiCad layouts of 6 open source designs using the TPS55340RTER.

What resistor goes on the TPS55340RTER COMP pin?

The COMP pin has a series resistor on 6 of 6 designs, most often 2 kΩ (then 2.49 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS55340RTER.

Which microcontrollers do boards using the TPS55340RTER use?

Most are built on ESP32 (2) and ESP8266 (1).

How big is a typical board using the TPS55340RTER?

The median is 90 × 83.5 mm, and 14% are two-layer designs.

What is the most popular open source board using the TPS55340RTER?

By GitHub stars, Canjay by atopile, with 29 stars.

Can I simulate one of these boards using the TPS55340RTER before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part