8 open source boards using the TPS564257DRLR
Real designs built with the TPS564257DRLR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Anyon e motherboard
byrantech
133 × 92 mm258 parts6LMIT4.3kPIC
Neptune
Board-Folk
191.2 × 190.9 mm372 parts4LNo license175ESP32
LADA
milutintech
137.2 × 61.6 mm90 parts4LNo license1ESP32
E-GoCart
Obili69
128.4 × 70.9 mm105 parts4LNo license0ESP32
VCU3.0
milutintech
128.4 × 70.9 mm105 parts4LNo license0ESP32
VCU2.0
milutintech
137.2 × 61.6 mm87 parts4LNo license0ESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
S3 sensor board
benvonhandorf
20 × 100 mm68 parts4LMIT0
How designs wire the TPS564257DRLR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS564257DRLR connects to, and the resistors, capacitors and other passives placed on it.
- The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 10 µF (then 100 nF).
- The SW pin has a inductor on 6 of 6 designs, most often 3.3 µH (then 4.7 µH).
- The PG pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ.
- The FB pin has a resistor to GND on 6 of 6 designs, most often 10 kΩ (then 30 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: 12V 100% |
|
| SWpin 2 | Connected to: Signal 83% · 3.3V 17% |
|
| GNDpin 3 | Connected to: GND 100% | — |
| PGpin 4 | Connected to: Signal 100% |
|
| ENpin 5 | Connected to: Signal 100% |
|
| FBpin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Anyon e motherboard by byrantech, Neptune by Board-Folk, LADA by milutintech and S3 sensor board by benvonhandorf.
The TPS564257DRLR in open source designs
The gallery holds 8 open source boards using the TPS564257DRLR from 6 GitHub repositories; a typical one measures about 130.7 × 70.8 mm and carries around 105 components.
100% use four copper layers or more, and 38% carry an open source license.
The most starred is Anyon e motherboard by byrantech.
Parts used alongside the TPS564257DRLR
What boards using the TPS564257DRLR are built for
TPS564257DRLR: common questions
Where can I find a TPS564257DRLR reference design?
Each of the 8 boards on this page is a real design using the TPS564257DRLR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TPS564257DRLR VIN pin?
The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the TPS564257DRLR.
How is the TPS564257DRLR SW pin connected?
The SW pin has a inductor on 6 of 6 designs, most often 3.3 µH (then 4.7 µH). Counted from the KiCad layouts of 6 open source designs using the TPS564257DRLR.
What pull-up resistor is used on the TPS564257DRLR PG pin?
The PG pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the TPS564257DRLR.
What parts are used alongside the TPS564257DRLR?
The ADS1015IDGST, BC817, BTS716GB, C2913204 and CP2102N-A02-GQFN28R appear in the most repositories here.
Which microcontrollers do boards using the TPS564257DRLR use?
Most are built on ESP32 (6) and PIC (1).
How big is a typical board using the TPS564257DRLR?
The median is 130.7 × 70.8 mm, and 0% are two-layer designs.
What is the most popular open source board using the TPS564257DRLR?
By GitHub stars, Anyon e motherboard by byrantech, with 4,264 stars.
Can I simulate one of these boards using the TPS564257DRLR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.