8 open source boards using the MCP2515-I/ST
Real designs built with the MCP2515-I/ST, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
LADA
milutintech
137.2 × 61.6 mm90 parts4LNo license1ESP32
E-GoCart
Obili69
128.4 × 70.9 mm105 parts4LNo license0ESP32
VCU3.0
milutintech
128.4 × 70.9 mm105 parts4LNo license0Nordic nRF
Nrf9151-modbus
mathijsmeulendijks
86 × 56 mm95 parts4LNo license0AVR/Arduino
Universal can board
franc0r
49.3 × 59.4 mm77 parts2LBSD-3-Clause0Anchor hat
nhnifong
65 × 30 mm42 parts4LNo license3ESP32
VCU2.0
milutintech
137.2 × 61.6 mm87 parts4LNo license0Interface board
TrendBit
65 × 56 mm121 parts2LGPL-3.00
How designs wire the MCP2515-I/ST
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MCP2515-I/ST connects to, and the resistors, capacitors and other passives placed on it.
- The OSC2 pin has a capacitor to GND on 7 of 7 designs, most often 22 pF (then 11 pF).
- The OSC2 pin has a crystal on 7 of 7 designs, most often 12 MHz (then 16 MHz).
- The OSC1 pin has a crystal on 7 of 7 designs, most often 12 MHz (then 16 MHz).
- The OSC1 pin has a capacitor to GND on 7 of 7 designs, most often 22 pF (then 11 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CLKOUTSOFpin 3 | Connected to: Not connected 100% | — |
| TX0RTS#pin 4 | Connected to: Not connected 43% · a signal 43% |
|
| TX1RTS#pin 5 | Connected to: Not connected 43% · a signal 43% |
|
| NCpin 6 | Connected to: Not connected 100% | — |
| TX2RTS#pin 7 | Connected to: Not connected 43% · a signal 43% |
|
| OSC2pin 8 | Connected to: Signal 100% |
|
| OSC1pin 9 | Connected to: Signal 100% |
|
| VSSpin 10 | Connected to: GND 100% | — |
| RX1BF#pin 11 | Connected to: Not connected 100% | — |
| RX0BF#pin 12 | Connected to: Not connected 100% | — |
| NC/2pin 15 | Connected to: Not connected 100% | — |
| RESET#pin 19 | Connected to: Signal 86% |
|
| VDDpin 20 | Connected to: 3.3V 100% | — |
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Anchor hat by nhnifong, LADA by milutintech, Universal can board by franc0r and Nrf9151-modbus by mathijsmeulendijks.
The MCP2515-I/ST in open source designs
The gallery holds 8 open source boards using the MCP2515-I/ST from 7 GitHub repositories; a typical one measures about 107.2 × 60.5 mm and carries around 93 components.
75% use four copper layers or more, and 25% carry an open source license.
The most starred is Anchor hat by nhnifong.
Parts used alongside the MCP2515-I/ST
Microcontrollers on boards using the MCP2515-I/ST
What boards using the MCP2515-I/ST are built for
MCP2515-I/ST: common questions
Where can I find a MCP2515-I/ST reference design?
Each of the 8 boards on this page is a real design using the MCP2515-I/ST. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP2515-I/ST OSC2 pin connected?
The OSC2 pin has a capacitor to GND on 7 of 7 designs, most often 22 pF (then 11 pF). Counted from the KiCad layouts of 7 open source designs using the MCP2515-I/ST.
How is the MCP2515-I/ST OSC1 pin connected?
The OSC1 pin has a crystal on 7 of 7 designs, most often 12 MHz (then 16 MHz). Counted from the KiCad layouts of 7 open source designs using the MCP2515-I/ST.
What pull-up resistor is used on the MCP2515-I/ST RESET# pin?
The RESET# pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 7 open source designs using the MCP2515-I/ST.
What parts are used alongside the MCP2515-I/ST?
The MCP2551-I-SN, ADS1015IDGST, BC817, BTS716GB and C2913204 appear in the most repositories here.
Which microcontrollers do boards using the MCP2515-I/ST use?
Most are built on ESP32 (4), AVR/Arduino (1) and Nordic nRF (1).
How big is a typical board using the MCP2515-I/ST?
The median is 107.2 × 60.5 mm, and 25% are two-layer designs.
What is the most popular open source board using the MCP2515-I/ST?
By GitHub stars, Anchor hat by nhnifong, with 3 stars.
Can I simulate one of these boards using the MCP2515-I/ST before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.