8 open source boards using the TXS0102DCUR
Real designs built with the TXS0102DCUR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
IMX6 Demo Board from REF
ts-manuel
80 × 70 mm465 parts6LGPL-3.010Mip servo controller
Mipot-Hi-Tech
100 × 90 mm202 parts4LCustom license3ESP32
GridWatcher
kylerichter36-coder
113.4 × 69.2 mm79 parts2LNo license3STM32
IdeFIX
GAULAvionique
100 × 60 mm83 parts2LNo license1Boardoza MLX90640 Thermal Camera Breakout Board
Boardoza
20 × 20 mm12 parts2LCC-BY-SA-4.00I.MX6 Demo Board
ts-manuel
80 × 70 mm455 parts6LGPL-3.010Bwlr1f prog
teapotlaboratories
61.2 × 26.1 mm40 parts2LNo license0DVI receiver
openconcepts-ar
43 × 25.8 mm52 parts4LCustom license1
How designs wire the TXS0102DCUR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TXS0102DCUR connects to, and the resistors, capacitors and other passives placed on it.
- The VCCA pin has a decoupling capacitor on 7 of 7 designs, most often 100 nF (then 220 nF).
- The VCCB pin has a decoupling capacitor on 7 of 7 designs, most often 100 nF (then 220 nF).
- The OE pin has a pull-up to 5V on 3 of 7 designs, most often 82 kΩ (then 10 kΩ).
- The OE pin has a capacitor to GND on 3 of 7 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VCCApin 3 | Connected to: 3.3V 100% |
|
| OEpin 6 | Connected to: Signal 57% · 1.8V 43% |
|
| VCCBpin 7 | Connected to: 3.3V 86% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include I.MX6 Demo Board by ts-manuel, GridWatcher by kylerichter36-coder, Mip servo controller by Mipot-Hi-Tech and IdeFIX by GAULAvionique.
The TXS0102DCUR in open source designs
The gallery holds 8 open source boards using the TXS0102DCUR from 7 GitHub repositories; a typical one measures about 80 × 64.6 mm and carries around 81 components.
50% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is IMX6 Demo Board from REF by ts-manuel.
Parts used alongside the TXS0102DCUR
What boards using the TXS0102DCUR are built for
TXS0102DCUR: common questions
Where can I find a TXS0102DCUR reference design?
Each of the 8 boards on this page is a real design using the TXS0102DCUR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TXS0102DCUR VCCA pin?
The VCCA pin has a decoupling capacitor on 7 of 7 designs, most often 100 nF (then 220 nF). Counted from the KiCad layouts of 7 open source designs using the TXS0102DCUR.
What decoupling capacitors do designs use on the TXS0102DCUR VCCB pin?
The VCCB pin has a decoupling capacitor on 7 of 7 designs, most often 100 nF (then 220 nF). Counted from the KiCad layouts of 7 open source designs using the TXS0102DCUR.
What pull-up resistor is used on the TXS0102DCUR OE pin?
The OE pin has a pull-up to 5V on 3 of 7 designs, most often 82 kΩ (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the TXS0102DCUR.
Which microcontrollers do boards using the TXS0102DCUR use?
Most are built on ESP32 (1) and STM32 (1).
How big is a typical board using the TXS0102DCUR?
The median is 80 × 64.6 mm, and 50% are two-layer designs.
What is the most popular open source board using the TXS0102DCUR?
By GitHub stars, IMX6 Demo Board from REF by ts-manuel, with 10 stars.
Can I simulate one of these boards using the TXS0102DCUR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.