13 open source boards using the USB6B1
Real designs built with the USB6B1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Lea m8f board
Opendigitalradio
37.2 × 43.8 mm33 parts2LCC-BY-SA-4.016Nordic nRF
Keyboard
GlassyBridge
314.3 × 137 mm356 parts2LMIT2AVR/Arduino
Macropad
vlee6
58.5 × 80.9 mm52 parts2LNo license2AVR/Arduino
Mithril panneled
sanfeps
132.8 × 138.8 mm216 parts4LNo license1AVR/Arduino
Controller
listofoptions
198.2 × 38.1 mm45 parts2LGPL-2.01STM32
BuuKeeb
buu342
431 × 122.3 mm447 parts2LNo license0STM32
BUT Pneumobil - ECU board
kajusK
143.8 × 80 mm261 parts2LNo license0RP2040/RP2350
MacroBoard
NoxAevi
403.8 × 137.1 mm227 parts2LMIT0RP2040/RP2350
Isolated rp2040 debugger
peterheinrich
91 × 44 mm63 parts4LNo license0ESP32
Idk pad
idksarah
140 × 79.4 mm41 parts2LNo license0AVR/Arduino
Mithril
sanfeps
269.8 × 158.8 mm211 parts4LNo license1STM32
BUT Pneumobil - HMI
kajusK
133.5 × 95 mm115 parts2LNo license0STM32
BUT Pneumobil - Radio to USB converter
kajusK
37.2 × 24 mm24 parts2LNo license0
How designs wire the USB6B1
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the USB6B1 connects to, and the resistors, capacitors and other passives placed on it.
- The I/O1 pins have a series resistor on 8 of 10 designs, most often 22 Ω (then 27 Ω).
- The I/O2 pins have a series resistor on 8 of 10 designs, most often 22 Ω (then 27 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VBUSpin 1, 8 | Connected to: VBUS 60% · a signal 40% |
|
| I/O1pin 2, 7 | Connected to: A connector 50% |
|
| I/O2pin 3, 6 | Connected to: A connector 50% |
|
| GNDpin 4, 5 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lea m8f board by Opendigitalradio, Keyboard by GlassyBridge, Macropad by vlee6 and Controller by listofoptions.
The USB6B1 in open source designs
The gallery holds 13 open source boards using the USB6B1 from 10 GitHub repositories; a typical one measures about 139.9 × 80.8 mm and carries around 115 components.
77% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.
The most starred is Lea m8f board by Opendigitalradio.
Parts used alongside the USB6B1
Microcontrollers on boards using the USB6B1
What boards using the USB6B1 are built for
USB6B1: common questions
Where can I find a USB6B1 reference design?
Each of the 13 boards on this page is a real design using the USB6B1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the USB6B1 I/O1 pin?
The I/O1 pins have a series resistor on 8 of 10 designs, most often 22 Ω (then 27 Ω). Counted from the KiCad layouts of 10 open source designs using the USB6B1.
What resistor goes on the USB6B1 I/O2 pin?
The I/O2 pins have a series resistor on 8 of 10 designs, most often 22 Ω (then 27 Ω). Counted from the KiCad layouts of 10 open source designs using the USB6B1.
What parts are used alongside the USB6B1?
The ATmega32U4-A, NCP1117-3.3_SOT223 and RP2040 appear in the most repositories here.
Which microcontrollers do boards using the USB6B1 use?
Most are built on AVR/Arduino (4), STM32 (4), RP2040/RP2350 (2) and ESP32 (1).
How big is a typical board using the USB6B1?
The median is 139.9 × 80.8 mm, and 77% are two-layer designs.
What is the most popular open source board using the USB6B1?
By GitHub stars, Lea m8f board by Opendigitalradio, with 16 stars.
Can I simulate one of these boards using the USB6B1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.