8 open source boards using the VL53L0CXV0DH1
Real designs built with the VL53L0CXV0DH1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Microbot v1.1
Freimor
185 × 58.6 mm190 parts4LNo license0Astra-Companion-NOISEEE
atireksd11
122 × 140 mm103 parts4LNo license0AVR/Arduino
Proxiwave-D
ampnics
50 × 100 mm44 parts2LNo license0STM32
ToF-Time of-Flight-Sensor
bluefeng2
20.3 × 43.5 mm23 parts2LNo license0AVR/Arduino
Airtap
ajkumar-1907
50 × 100 mm44 parts2LMIT0ESP32
Control board
Freimor
90 × 110 mm105 parts4LNo license0AVR/Arduino
Airtap
ajkumar-1907
50 × 100 mm44 parts2LMIT0ESP32
Control board(2024-10-31 160845)
Freimor
90 × 110 mm105 parts4LNo license0
How designs wire the VL53L0CXV0DH1
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the VL53L0CXV0DH1 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to AVDD on 6 of 6 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The SCL pin has a pull-up to AVDD on 6 of 6 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The XSHUT pin has a pull-up to AVDD on 5 of 6 designs, most often 10 kΩ.
- The AVDDVCSEL pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF (then 4.7 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| AVDDVCSELpin 1 | Connected to: AVDD 100% |
|
| AVSSVCSELpin 2 | Connected to: GND 100% | — |
| GNDpin 3, 4, 6, 12 | Connected to: GND 100% | — |
| XSHUTpin 5 | Connected to: The microcontroller 50% · 3.3V 17% |
|
| GPIO1pin 7 | Connected to: Signal 67% · not connected 33% |
|
| DNCpin 8 | Connected to: Not connected 100% | — |
| SDApin 9 | Connected to: The microcontroller 83% |
|
| SCLpin 10 | Connected to: The microcontroller 83% |
|
| AVDDpin 11 | Connected to: AVDD 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Airtap by ajkumar-1907, Airtap by ajkumar-1907, Proxiwave-D by ampnics and Astra-Companion-NOISEEE by atireksd11.
The VL53L0CXV0DH1 in open source designs
The gallery holds 8 open source boards using the VL53L0CXV0DH1 from 6 GitHub repositories; a typical one measures about 70 × 100 mm and carries around 74 components.
50% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is Microbot v1.1 by Freimor.
Parts used alongside the VL53L0CXV0DH1
Microcontrollers on boards using the VL53L0CXV0DH1
What boards using the VL53L0CXV0DH1 are built for
VL53L0CXV0DH1: common questions
Where can I find a VL53L0CXV0DH1 reference design?
Each of the 8 boards on this page is a real design using the VL53L0CXV0DH1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the VL53L0CXV0DH1 SDA pin?
The SDA pin has a pull-up to AVDD on 6 of 6 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 6 open source designs using the VL53L0CXV0DH1.
What pull-up resistor is used on the VL53L0CXV0DH1 SCL pin?
The SCL pin has a pull-up to AVDD on 6 of 6 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 6 open source designs using the VL53L0CXV0DH1.
What pull-up resistor is used on the VL53L0CXV0DH1 XSHUT pin?
The XSHUT pin has a pull-up to AVDD on 5 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the VL53L0CXV0DH1.
Which microcontrollers do boards using the VL53L0CXV0DH1 use?
Most are built on AVR/Arduino (3), ESP32 (3) and STM32 (1).
How big is a typical board using the VL53L0CXV0DH1?
The median is 70 × 100 mm, and 50% are two-layer designs.
What is the most popular open source board using the VL53L0CXV0DH1?
By GitHub stars, Microbot v1.1 by Freimor, with 0 stars.
Can I simulate one of these boards using the VL53L0CXV0DH1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.